Search:

Type: Posts; User: snookerd1206

Page 1 of 20 1 2 3 4

Search: Search took 0.12 seconds.

  1. Thread: Axle slop

    by snookerd1206
    Replies
    9
    Views
    392

    I found some slop in my push rod ends, wrapped...

    I found some slop in my push rod ends, wrapped them all with some electrical tape, no slop there, next I took the stock 17mm Adapters and shaved the ring off the back making a flat surface across...
  2. Replies
    4
    Views
    519

    Tighten your slipper clutch up a bit.

    Tighten your slipper clutch up a bit.
  3. Replies
    10
    Views
    301

    Looks great man, hope you are having fun!,...

    Looks great man, hope you are having fun!, welcome to the forums, and god bless.
  4. Replies
    6
    Views
    348

    There's really no need for upgrades per say, you...

    There's really no need for upgrades per say, you could get yourself a good set of hex wrenches if you don't have those already, Also a good upgrade though not cheap is to replace the dual stock...
  5. Wow, sorry you got sniped northern, sometimes it...

    Wow, sorry you got sniped northern, sometimes it is better to not say anything right. Good luck finding another set. God bless
  6. Depending on where you are located you can get...

    Depending on where you are located you can get the non waterproof MMM/2650 or 2200 combo from
    Castle creations for 215 check the site and look under the garage sale banner. Good luck and have fun. ...
  7. Replies
    7
    Views
    657

    As recommended, you should upgrade to the...

    As recommended, you should upgrade to the brushless tranny as it can handle the power a lot better than the nitro tranny, look on ebay there are usually quite a few there or ask around here on the...
  8. Replies
    29
    Views
    1,647

    Seems like it would be a great place for a...

    Seems like it would be a great place for a summit!!
  9. Replies
    46
    Views
    2,921

    Looks good, why no wing? I would think this...

    Looks good, why no wing? I would think this would help with control or does it give too much drag?? Anyway body is killer and hope you do well. Good luck and god bless. And don't forget some...
  10. Replies
    24
    Views
    342

    In my opinion you should really give the dewalt a...

    In my opinion you should really give the dewalt a try before you spend too much, $30-40 for a dewalt motor, or you need an esc that can handle your sensored motor. And to be honest this truck just...
  11. Be careful with the integy skids, I had similar...

    Be careful with the integy skids, I had similar ones on my erbe and they bend at the curve, and once bent they get weaker. Good luck truck looks good hope to see the new setup soon. Don't forget to...
  12. Well at least you are getting a new one. Traxxas...

    Well at least you are getting a new one. Traxxas cm is top notch. Hope you get it back up and running soon. God bless.


    Sent from my iPhone 5
  13. Time for an MMP. Good luck and hope you get it...

    Time for an MMP. Good luck and hope you get it sorted out man. I guess it goes with saying that customer service goes a long way when things like this occur. You said you are out 75 dollars right...
  14. Did you try using the castle link and maybe...

    Did you try using the castle link and maybe change the firmware, or do you know for sure the esc is toast??


    Sent from my iPhone 5
  15. Replies
    67
    Views
    1,542

    I would listen to what pav is trying to tell you...

    I would listen to what pav is trying to tell you he knows a lot about these things, JMO but listen to the man he knows what he is talking about. Good luck and god bless.


    Sent from my iPhone 5
  16. Hey mayor have you looked at buying a new one...

    Hey mayor have you looked at buying a new one from tower hobbies or online?? I don't know if they have it right now but normally if you become a tower hobby member you get discount codes and could...
  17. Replies
    32
    Views
    7,361

    A good idea before putting the Velcro on is to...

    A good idea before putting the Velcro on is to take some 91% rubbing alcohol and wipe the areas that you are going to Velcro down and also wash your hands and try not to touch the sticky side, start...
  18. Replies
    11
    Views
    807

    Get the KH motor mount and don't look back. I...

    Get the KH motor mount and don't look back. I would also recommend a good bearing for the KH mount as I have heard and seen a few posts where the KH bearings have seized. This is JMO, good luck and...
  19. Replies
    26
    Views
    478

    2000kv or around there. You won't be...

    2000kv or around there. You won't be disappointed with the Tekin system. It's worth the money. Good luck and keep us posted on what you end up doing. God bless.


    Sent from my iPhone 5
  20. Replies
    30
    Views
    2,254

    The mmm2 is not sensored, neither is the motor. ...

    The mmm2 is not sensored, neither is the motor. It's a sensor less combo the mmm2/2200kv and if you like to crawl a lot will not be the best setup, for general bashing its fine but because its a non...
  21. Replies
    37
    Views
    1,111

    How much did you pay for the esc? Sent...

    How much did you pay for the esc?


    Sent from my iPhone 5
  22. Replies
    8
    Views
    389

    I was geared 14/62 on mine but you have to watch...

    I was geared 14/62 on mine but you have to watch the temps as the motor can get hot. Good luck and god bless.


    Sent from my iPhone 5
  23. Replies
    28
    Views
    740

    Get yourself some good lipos and a good charger. ...

    Get yourself some good lipos and a good charger. When things break upgrade them to better parts. As far as mods go, a lot of people shim the diffs to prevent stripping of diff gears. Do a search...
  24. Replies
    27
    Views
    1,953

    Google castle creations and look for the...

    Google castle creations and look for the clearance or bargain sale banner on the site. Good luck with whatever you choose and god bless.


    Sent from my iPhone 5
  25. Replies
    37
    Views
    1,111

    Now that the mmm2 is out they have the og version...

    Now that the mmm2 is out they have the og version on sale for 215, that's with either motor, 2200 or 2650, to me it's a good deal but this is JMO.


    Sent from my iPhone 5
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4