Search:

Type: Posts; User: bmccle

Page 1 of 2 1 2

Search: Search took 0.10 seconds.

  1. Replies
    6
    Views
    255

    Thanks. This is good stuff!!

    Thanks. This is good stuff!!
  2. Replies
    6
    Views
    255

    I am definitely hard on the brakes...always have...

    I am definitely hard on the brakes...always have been...I think it is cool on slick concrete and or sand. Can you give me a link or some pictures on how to shim them? I've looked and can't find...
  3. Replies
    6
    Views
    255

    I replaced the large ring gear. One of the...

    I replaced the large ring gear. One of the 'leftover' rings I had was actually two rings, one really thin one fit inside the other on. The did seem to be about as big around as the bearing if I...
  4. Replies
    6
    Views
    255

    Differential/transmission problem

    My E Maxx brushless makes a clicking sound when I try to stop. It has now gotten to where it does it some when I try to go forward and the front wheel drive is almost non-existent. Is this likely a...
  5. I don't think there really would be an advantage...

    I don't think there really would be an advantage to running the aluminum under plastic. I replaced mine first with aluminum skids but they kept bending so much they just got to where they weren't...
  6. Great info. Thanks. (to 87 Gn)

    Great info. Thanks. (to 87 Gn)
  7. Trust me, the most important thing to do is make...

    Trust me, the most important thing to do is make sure that LVC is set to cutoff the lipos at 3.4 volts per cell. When I purchased my EMaxx the default setting was 3.0. I ruined at least 6 lipos...
  8. Replies
    63
    Views
    3,153

    Mine came with the white as well but I "upgraded"...

    Mine came with the white as well but I "upgraded" my shocks to the big bores. Maybe the big bores are supposed to be better but they come with mushy red springs and it makes the truck ride very low...
  9. Thread: Mamba Monster

    by bmccle
    Replies
    9
    Views
    1,560

    I saw some of those, I think? You opened up the...

    I saw some of those, I think? You opened up the end with the wires right? I opened the other end. I was looking for bearings but there wasn't one on that end...like I said, I got chicken because I...
  10. Thread: Mamba Monster

    by bmccle
    Replies
    9
    Views
    1,560

    No, I opened it from the drive shaft end. ...

    No, I opened it from the drive shaft end. Definitely NOT a circuit card. I will try to figure out how to load a picture.
  11. Replies
    304
    Views
    16,737

    Sweet! Now you get to buy more stuff!! Go with...

    Sweet! Now you get to buy more stuff!! Go with aluminum bulks..but make sure they are built solid or they will bend.
  12. Get Zippy's from Hobbypartz. Very inexpensive. ...

    Get *****'s from Hobbypartz. Very inexpensive. Also, do not forget to set your auto shutoff to 3.4 volts are you will destroy your lipos.
  13. Thread: Mamba Monster

    by bmccle
    Replies
    9
    Views
    1,560

    Mamba Monster

    Does anyone have a picture of what the inside of the mamba monster looks like. Specifically, when I remove the end cap/cover there is a silver looking dish that has something dark blue and hard in...
  14. Replies
    63
    Views
    3,153

    Where can you buy the UE shocks. I cannot find...

    Where can you buy the UE shocks. I cannot find them and I have looked and I have typed in unlimited engineering suspension as someone suggested.
  15. Replies
    63
    Views
    3,153

    I did a lot of research before I bouught them. ...

    I did a lot of research before I bouught them. That is why I am on here warning people of what they are going to get. I put 60 wt oil in them and they are still too mushy. I run 6s and it bottoms...
  16. Replies
    23
    Views
    1,116

    Why would you have to buy the whole kit? Just...

    Why would you have to buy the whole kit? Just replace what broke?
  17. Replies
    63
    Views
    3,153

    Don't waste your money on the big bores. They...

    Don't waste your money on the big bores. They make your truck sit way too low and they are mush. you will bottom out on every little bump. I am mad that I wasted my money on them.

    Edited for...
  18. Replies
    29
    Views
    500

    Check your parts list

    Check your parts list
  19. Thread: Maintenance

    by bmccle
    Replies
    4
    Views
    274

    Maintenance

    Is there anywhere that Traxxas explains what all to maintain, clean, lubricate and what to clean/lubricate it with? I know there is a section in the back of the manual but it is very general and,...
  20. Replies
    7
    Views
    320

    Ok, time to show my ignorance again. When you...

    Ok, time to show my ignorance again. When you say to "unmesh" the spur and pinion. You meant to just tak off the small gear, right? And, how the heck am I supposed to know if something is...
  21. Replies
    178
    Views
    10,546

    Were the rpm a arms a tight fit on the gh bulks? ...

    Were the rpm a arms a tight fit on the gh bulks? Is your steering (bellcrank?) hitting the lower a arm - hinge pin?
  22. Replies
    23
    Views
    1,116

    Which bearings did u replace them with?

    Which bearings did u replace them with?
  23. Replies
    63
    Views
    3,153

    Do you havehave a link?

    Do you havehave a link?
  24. Thread: who runs 6s?

    by bmccle
    Replies
    17
    Views
    659

    I run 6s. Only driveshaft problem I've had is...

    I run 6s. Only driveshaft problem I've had is once when I got in tall grass with big joes on. Grass somehow wrapped around the tires and locked them up. Instead of going and picking up my truck to...
  25. Replies
    63
    Views
    3,153

    What flm bulks and shock towers did you buy? I...

    What flm bulks and shock towers did you buy? I put the traxxas shocks on mine and I do not like them. They are mush. So I was considering swapping out my shock towers so the bigger shocks would...
Results 1 to 25 of 41
Page 1 of 2 1 2