Search:

Type: Posts; User: nitrobasher

Page 1 of 20 1 2 3 4

Search: Search took 0.38 seconds.

  1. Replies
    2,131
    Views
    375,418

    Sticky: Steve- email has been sent. :)

    Steve- email has been sent. :)
  2. Replies
    12
    Views
    415

    Im not sure if they still sell it, but I have...

    Im not sure if they still sell it, but I have used a kyosho filter that has a large black plastic cover over the foam. I think it was designed for racing in the mud but it keeps the water out nicely....
  3. Replies
    2,131
    Views
    375,418

    Sticky: TRX 3.3 Will do Steve. Just making sure,...

    TRX 3.3



    Will do Steve. Just making sure, is your e-mail address still the same?
  4. Replies
    2,131
    Views
    375,418

    Sticky: No problem Steve. Here are some more pics of the...

    No problem Steve. Here are some more pics of the RC Pro Finals...

    The Monster Truck A-Main drivers.
    http://i19.photobucket.com/albums/b174/nitrobasher1/DSC00314.jpg

    Tim Roberts and myself....
  5. Replies
    2,131
    Views
    375,418

    Sticky: Great. Hope to meet and race with ya sometime in...

    Great. Hope to meet and race with ya sometime in 08.
  6. Replies
    2,131
    Views
    375,418

    Sticky: yes, I have only raced there once though. I...

    yes, I have only raced there once though. I usually go to hobby hut in Audubon, PA for club racing but I hope to make it to blue diamond more next year.
  7. Replies
    2,131
    Views
    375,418

    Sticky: Thanks for the correction Anthony. It's Mark....

    Thanks for the correction Anthony. It's Mark. Good job on your finish in gas truck. I have a picture of you that I will e-mail to you.
  8. If fuel is spraying out of the engine, you will...

    If fuel is spraying out of the engine, you will have a hard time getting it running. Since you took the cooling head off the engine, make sure you replaced the copper shim that goes under the...
  9. Thread: Diff leak

    by nitrobasher
    Replies
    11
    Views
    408

    It will still work fine but you wont have any...

    It will still work fine but you wont have any diff oil left in there. You would probably notice better handling if you replaced the diff oil.
  10. Thread: Diff leak

    by nitrobasher
    Replies
    11
    Views
    408

    If you are a basher, I'd say rebuild the diffs...

    If you are a basher, I'd say rebuild the diffs after every gallon. If you are a racer, I'd recommend rebuilding them after every 2-3 race weekends. Its always good to just open them up and clean them...
  11. Thread: Diff leak

    by nitrobasher
    Replies
    11
    Views
    408

    After a certain amount of time, every diff needs...

    After a certain amount of time, every diff needs to be rebuilt. Its pretty easy and doesnt cost much. You will need part #5381(diff carrier/x rings) and a bottle of diff oil (stock is 30k front and...
  12. Replies
    4
    Views
    430

    Its just normal wear. They shouldn't snap or give...

    Its just normal wear. They shouldn't snap or give you any problems but its a good idea to keep a pack of rod ends in your pit box just in case. You wouldn't want to be out bashing and break one and...
  13. Replies
    19
    Views
    865

    Make sure the ends are not extremely tightened...

    Make sure the ends are not extremely tightened down on the pushrod. The pressure from overtightening can put stress on the ends and any impact can cause the ends to crack.
  14. Replies
    23
    Views
    509

    put the P1 rockers back on and put the long...

    put the P1 rockers back on and put the long travel springs on it. It will be extremely bouncy over jumps but you should definitely be able to wheelie. There shouldnt be any need to change the pistons...
  15. Replies
    5
    Views
    486

    Thanks. Im Mark by the way. Great job making the...

    Thanks. Im Mark by the way. Great job making the A. The whole weekend was exciting. It was a lot of good racing. The track was awesome and took some practice to figure out. I had a lot of fun and...
  16. Replies
    17
    Views
    402

    Yes, you are correct, however, the same method is...

    Yes, you are correct, however, the same method is printed in both the 2.5 and 3.3 engine manuals so traxxas recommends the same method on both engines.
  17. Replies
    32
    Views
    1,375

    looks great. definitely different from the other...

    looks great. definitely different from the other rocker-connected setups out there. do you plan on adding one in the rear too?
  18. Replies
    1
    Views
    158

    yes the servo saver parts are interchangable. the...

    yes the servo saver parts are interchangable. the only thing different about the steering between the two models is the length of the small servo linkage rods.
  19. Replies
    17
    Views
    402

    No problem. glad I could help.

    No problem. glad I could help.
  20. Replies
    17
    Views
    402

    Yes you can. The 3.3 and 2.5 can be broken in...

    Yes you can. The 3.3 and 2.5 can be broken in using the same procedure.
  21. Replies
    14
    Views
    572

    The best thing to do is watch the truggies and...

    The best thing to do is watch the truggies and check out the areas of the track that you lose time on. Then adjust your revo to handle better in that section. I would definitely go with the center...
  22. Replies
    22
    Views
    315

    Yep, you can use the crowd pleazer for the revo...

    Yep, you can use the crowd pleazer for the revo 3.3 body. Im not sure if you know or not, but they come unpainted and uncut so you will need to buy some paint for lexan bodies and be sure to clean...
  23. Replies
    22
    Views
    315

    Yes, if you have an extended chassis, you will...

    Yes, if you have an extended chassis, you will need a revo 3.3 body, however a revo 2.5 body will fit, you just have to drill the front body mount holes about 1 inch further out. The revo 2.5 body...
  24. Replies
    2
    Views
    176

    Take your transmission apart and examine the...

    Take your transmission apart and examine the 2-speed clutch. The arm that swings out to engage the 2nd speed gear may have a burr on the end that is keeping it engaged all the time.
  25. Replies
    11
    Views
    367

    It sounds like your piston is in backwards. The...

    It sounds like your piston is in backwards. The cutout is supposed to face the carb or cluch. If that doesn't work, make sure your clutch nut is tight. If you still can't get it to start, try heating...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4