Search:

Type: Posts; User: wolverine1267

Page 1 of 16 1 2 3 4

Search: Search took 0.17 seconds.

  1. Replies
    0
    Views
    260

    Spur/ Brake Poblem ?

    I just came across a problem with my Rusty that I never came across before, and it's stumping me as to what to do to correct it.
    I attached a new spur to my tranny and tightened it down all the...
  2. Replies
    4
    Views
    319

    I sent it to him already... Sorry.

    I sent it to him already... Sorry.
  3. Replies
    10
    Views
    439

    Could be a bad gear mesh, or you could have some...

    Could be a bad gear mesh, or you could have some chassis flex causing it.
    Are you jumping with it when it happens ? Or does it happen during normal running ?
  4. Replies
    4
    Views
    319

    I have a carb body w/ LSN, but the HSN has been...

    I have a carb body w/ LSN, but the HSN has been broken off.
    You can have it if you want. Just PM me your address and I'll send it to you.
    You can kick back the shipping after you recieve it.
  5. Go to e-bay and type this in the search....

    Go to e-bay and type this in the search.
    260047108516 29.99 + 1.69 shipping
  6. Replies
    17
    Views
    579

    What he is saying is, that the motor has the same...

    What he is saying is, that the motor has the same pattern for the mounts as the 2.5. It's basicly a 2.5 with a bigger displacement. Not all .26's will fit that mount only midblock maxx motors will...
  7. Replies
    12
    Views
    352

    RRP ring and pinnion, They will hold up. Link...

    RRP ring and pinnion, They will hold up. Link
    And maybe some stronger diff housings.
  8. Thread: sleeves

    by wolverine1267
    Replies
    4
    Views
    228

    2.5 piston and sleeve click here...

    2.5 piston and sleeve click here

    1.5 piston and sleeve click here

    They are not the same. And a bid difference in price.
  9. Replies
    9
    Views
    297

    That's good that the screws bent. Think about...

    That's good that the screws bent.
    Think about it. If the screws did not bend, something else would.
  10. Replies
    6
    Views
    257

    Here you go FLM PRODUCTS...

    Here you go FLM PRODUCTS
  11. Replies
    10
    Views
    357

    You can just get yourself a different set of...

    You can just get yourself a different set of crystals. Traxxas has a few different kinds. They are just a different color crystal.
  12. Replies
    6
    Views
    286

    If it's the "Picco.26 Maxx engine" Like this one...

    If it's the "Picco.26 Maxx engine" Like this one Picco .26 Maxx engine
    It will fit. The others have a larger crankcase witch makes it to large for the stock chassis
  13. Replies
    11
    Views
    344

    Try reading this Performance Guide...

    Try reading this Performance Guide . It has a lot of info on setting up your Maxx to handle better.
  14. That's a lot of torq that you will not need. The...

    That's a lot of torq that you will not need. The 5645 is plenty enough for what you you need.

    You don't have to pay that much. Get it on e-bay with "buy Now"
    for only $46.00 for the 5645Mg . Item...
  15. These seem to last pretty long, and they are not...

    These seem to last pretty long, and they are not to exspensive.
    Fastlane Diffs
  16. Replies
    9
    Views
    551

    Try reading this article, Suspention Tuning...

    Try reading this article, Suspention Tuning It will help you understand what you can do to get the best out of your Maxx.
  17. Replies
    18
    Views
    416

    It's not that hard. There are alot of people who...

    It's not that hard. There are alot of people who do it different ways.
    On the posts I set the body on where I think it looks best. I then reach through the wheel wells and put a small mark on the...
  18. Replies
    12
    Views
    415

    I noticed the leak when I had to replace a pull...

    I noticed the leak when I had to replace a pull start. The gaset behind the backplate was worn. So I sealed it up with O2 safe silicone. And the problem went away.
  19. Replies
    12
    Views
    415

    I had the same problem, it turned out that I had...

    I had the same problem, it turned out that I had a leak in my backplate. I sealed it up and it ran great with temps about 250
  20. If it's not re-centering with a new servo, look...

    If it's not re-centering with a new servo, look to see if your pillow ball caps are to tight. Having them to tight will keep it from re-centering. Just a sugestion.
  21. Replies
    8
    Views
    340

    Here you Go. e-hobbies...

    Here you Go. e-hobbies Type in the search bar 51402. You will find it there.
  22. Thread: engine?

    by wolverine1267
    Replies
    5
    Views
    217

    The CVR-X won't fit unless he has the 2.5 upgrade...

    The CVR-X won't fit unless he has the 2.5 upgrade kit. He has the Pro.15 engine and mounts.....................................................
    Here is what he will need for that to happen....
  23. Replies
    5
    Views
    315

    Try This. I anwsered it in your other post. No...

    Try This. I anwsered it in your other post.
    No Buck Tranny Mod.
  24. Replies
    3
    Views
    148

    Sorry "Street is Good" I didn't mean to post some...

    Sorry "Street is Good" I didn't mean to post some of the things you posted. You kinda beat me to it. LOL

    1- Your Right !! there is no set limit on how long a engine will last.
    If you keep...
  25. Replies
    10
    Views
    329

    This could have been the reason why you lost you...

    This could have been the reason why you lost you "top-end"and your "low-end" as you stated in one of your other posts.
    U.E. stuff don't usually come with "specific directions" so it makes it kind of...
Results 1 to 25 of 392
Page 1 of 16 1 2 3 4