Search:

Type: Posts; User: CornUponCob

Page 1 of 2 1 2

Search: Search took 0.30 seconds.

  1. Nevermind, it was just the really bad start of...

    Nevermind, it was just the really bad start of all the firmwares 1.24 or newer. I really hope they fix that. Went back to 1.24 and it was smooth again. . . servo is a bit slower, but still way...
  2. Erronous throttle response with MMM firmware 1.39 beta

    When I first got my MMM and 2200 about a year ago and installed it in my summit I updated the firmware to ~ 1.33 or whatever was current at the time. When I'd drive it there was a significant lag at...
  3. Replies
    4
    Views
    347

    Seems like the screw worked itself out. On its...

    Seems like the screw worked itself out. On its way out, once the screw was "out" of the other side of the yoke power was probably applied causing the screw side to be dug into more since now all the...
  4. Got the MM combo, I think the ESC is bad, should I buy a new one?

    If you are a serious crawler I can see how the MM combo is not the best setup, but for light bashing and long trail excursions it's awesome. Just on 4s the motor is plenty fast enough (geared 14x86)...
  5. I'll definitely accept the responsibility for...

    I'll definitely accept the responsibility for what I did. Same deal if I cut myself with a knife. . . I can't exactly be mad at knife makers for making a knife sharp.

    I still feel that given how...
  6. Reverse polaritied the VXL-3s but it still works. . .how?

    So I think hard case batteries are the worst thing in the world since you're able to plug the leads in backwards. I also think the battery hold down bar on the rustler isn't the best because it...
  7. Best way to prevent my dwalt motor brushes from sticking?

    Cliff notes:

    I know somebody else out there has been running the dewalt 14.4 motor way longer than I have, and I'm sure some of you have had your brushes stick before, so what did you determine to...
  8. Mostly trails and bashing (not jumping, but lots...

    Mostly trails and bashing (not jumping, but lots of hard accelerating and cornering on loose dirt / gravel). I also like to tie a kite to the truck and drive it around in big fields. I guess I do...
  9. Dewalt 14.4 vs Mamba monster Temps and runtimes

    Today I pushed the Dewalt 14.4 hard in ~ 90 degree heat on 5s running through the EVX2 (when I think was going into overvoltate protection when I first started running it today because they were...
  10. What's the name of the connector the LEDs use?

    I've been searching forever but I can't find an answer. It's the two prong connector with two humps.

    Also, the wires are marked with white dashes on one of the wires. Those dashes could be...
  11. I should have noted I had the RX plastic cover...

    I should have noted I had the RX plastic cover off when I first tested the motor. After putting it back on, glitching is a little more under control. . . maybe I can go to about 120 yards now before...
  12. Glitching at ~ 100 yards with dewalt 14.4 no caps, 2.4 GHz radio

    Based on the forum's advice, everybody said they weren't getting any glitching with no caps with the dewalt motor. . . that didn't seem to be the case for me. Stock I could go 200 yards or so (which...
  13. Part of the reason for me wiring the lights...

    Part of the reason for me wiring the lights outside of the receiver off their own battery and circuit is so I can more easilly turn them on and off, and I noticed as my batteries would fade the...
  14. I guess I worded my post extremely poorly (I just...

    I guess I worded my post extremely poorly (I just noticed). I know they're 8.4v fully charged, but since the summit lights get wired in sets of 2 in series, it would be 4.2v per LED, but yeah, my...
  15. Run summit LEDs and a cooling fan directly off 2s Lipo

    I've bought the lighbar for the summit, and re-wired the other LEDs out of the Rx box and will be wiring them through an external switch. I also bought a cooling fan for my motor. Question is if...
  16. Replies
    29
    Views
    2,792

    Just to let you know, it took 5 days for a LVA to...

    Just to let you know, it took 5 days for a LVA to run down a 2s 5000 mah lipo from fully charged down to 3.8v per cell. I had to do that when I had fully charged my batteries, but then my ESC died...
  17. Got new Lipos (already running lipo). . . what's the improved performance from?

    Still ~ 2 months new to the hobby so my only basis of comparison is:

    Stock NiMH batteries

    Venom 2s 5000 mah 50C hardcase batteries. The leads attach to the battery with bullets, then I'm using...
  18. Comprehensive list of the beefiest drivetrain upgrades for the summit?

    So I think long-term I'll keep the Summit as a rather low-speed trail / crawler truck, but something I've always been interested in is towing with the truck as well.

    I've seen the Scaniris videos...
  19. Thanks a bunch. This is exactly the diagram I...

    Thanks a bunch. This is exactly the diagram I was looking for.
  20. As far as I know, I shouldn't have to do any...

    As far as I know, I shouldn't have to do any re-wiring of the batteries that power the ESC and motor (unless a pesky grounding issue messes that up).

    A side goal of this is to keep the ESC's BEC...
  21. Wiring up a CC BEC Pro with a separate battery just for servos and lights.

    I wrote out a big long post, but then I decided that was stupid.

    Gonna get a CC BEC Pro and run it off a hardcase 2s 5000mah lipo. I don't plan on buying a receiver battery. I plan on having one...
  22. Somewhere near the front of the truck...

    Somewhere near the front of the truck horizontally. I'd probably make some kind of bracket to help hold them there. When I make the switch to BL, I'll probably move the ESC more forward so all the...
  23. Thanks for your reply. I've seen countless...

    Thanks for your reply. I've seen countless running videos of different vehicles on 5 and 6s, and I'm well aware the summit isn't really designed for 6s brushless power, but. . . yeah, I plan on...
  24. Thanks for your reply. I've seen countless...

    Thanks for your reply. I've seen countless running videos of different vehicles on 5 and 6s, and I'm well aware the summit isn't really designed for 6s brushless power, but. . . yeah, I plan on...
  25. Running 3x 2s lipos in series for 6s power for future BL upgrade

    I've exhaustively searched, but haven't found any definitive answers on this.

    I'm considering purchasing 6 of the ********** 7600 mah 2s batteries to use in my stock summit. I'd number the packs...
Results 1 to 25 of 30
Page 1 of 2 1 2