Search:

Type: Posts; User: danyvw

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    13
    Views
    1,161

    If you like the TSH1046 then just try the THS146H...

    If you like the TSH1046 then just try the THS146H or the TSH146C, they are way better. The power gain is like 20% more low/end.
  2. Replies
    10
    Views
    1,009

    Could be many things but the fact that the engine...

    Could be many things but the fact that the engine stops when temperature goes up and when is cool starts again is sign of a worn piston/sleeve so chances are that the engine is done.
  3. Replies
    7
    Views
    725

    ^^^^^+1 You could add the OS .18TZ

    ^^^^^+1 You could add the OS .18TZ
  4. Thread: Feeler thread

    by danyvw
    Replies
    6
    Views
    545

    Selling a good truck like is always a shame....

    Selling a good truck like is always a shame. Nobody will give you half of the money you spent on it.
  5. Replies
    31
    Views
    3,828

    I'm not so sure but hear that OS discontinued the...

    I'm not so sure but hear that OS discontinued the .21TM, today I was looking for a crankcase and is discontinued on Tower and other web stores. I don't know the reason and in the OS website there is...
  6. Replies
    10
    Views
    845

    Very nice collection lube. Congrats!

    Very nice collection lube. Congrats!
  7. Thread: Revo OS .28XZ

    by danyvw
    Replies
    170
    Views
    6,902

    You will need a better pipe for that engine, the...

    You will need a better pipe for that engine, the resonator will kill that OS.
  8. Thread: Stock shoes ?

    by danyvw
    Replies
    19
    Views
    602

    3 shoes clutch is the solution.

    3 shoes clutch is the solution.
  9. Replies
    724
    Views
    34,332

    Explode views part 5393

    Explode views
    part 5393
  10. Replies
    7
    Views
    764

    What's this thread about?

    What's this thread about?
  11. Thread: over heating

    by danyvw
    Replies
    21
    Views
    783

    ^^^^^^^^^+1 alucard, are you a writer? It's so...

    ^^^^^^^^^+1
    alucard, are you a writer? It's so nice reading your posts.
  12. Thread: clutch

    by danyvw
    Replies
    68
    Views
    1,453

    In your picture, do you see the upper gear? The...

    In your picture, do you see the upper gear? The one that is attached to the input shaft? That is the input gear, it has two sides, the one that you see and other in the back. It is probable that the...
  13. Replies
    4
    Views
    572

    Check the chassis. A bent chassis is one of the...

    Check the chassis. A bent chassis is one of the most common cause of a stripped spur gear.
  14. Thread: clutch

    by danyvw
    Replies
    68
    Views
    1,453

    The problem seems to be between the pads, slipper...

    The problem seems to be between the pads, slipper plate and pressure plate. The spur gear is moving with the pads but the pressure plate is not moving at all. Did you install the slipper plate...
  15. Thread: clutch

    by danyvw
    Replies
    68
    Views
    1,453

    Hey dude, are you sure you tighten the slipper...

    Hey dude, are you sure you tighten the slipper clutch nut? Looks like a lose slipper clutch as you can see the inner shaft is not moving just the spur and pads slipping on the disk.
  16. Thread: HPI Fuel

    by danyvw
    Replies
    2
    Views
    586

    I’ve never used but HPI is one of the best RC...

    I’ve never used but HPI is one of the best RC Companies on the market. Just remember to retune. If it’s too difficult go to factory settings and start from scratch.
  17. Thread: clutch

    by danyvw
    Replies
    68
    Views
    1,453

    I can't see any video, you can use youtube or...

    I can't see any video, you can use youtube or photobucket.
  18. Thread: Wings

    by danyvw
    Replies
    15
    Views
    793

    You can't find it because the best wheelie bar...

    You can't find it because the best wheelie bar for the Revo is a wing.
  19. Replies
    9
    Views
    723

    For the stockers (Geode on Maxxes) and TRX3.3 new...

    For the stockers (Geode on Maxxes) and TRX3.3 new Revo comes with 38/14.
  20. Thread: clutch

    by danyvw
    Replies
    68
    Views
    1,453

    The clutch bell should move freely when engine is...

    The clutch bell should move freely when engine is off or idling, when engine revs the clutch engage then the CB stops moving freely and start moving with the flywheel and the engine. When spring...
  21. Replies
    9
    Views
    723

    ^^^^^ +1. It will help a lot.

    ^^^^^ +1. It will help a lot.
  22. Replies
    61
    Views
    2,816

    Put Idle gap at 1mm and DON"T TUCH IT AGAIN. HSN...

    Put Idle gap at 1mm and DON"T TUCH IT AGAIN. HSN 4 Turns, LSN Flush with carb body and start tuning from there
  23. Thread: clutch

    by danyvw
    Replies
    68
    Views
    1,453

    For opening and disassembling the tranny the OP...

    For opening and disassembling the tranny the OP had to have the input shaft with the spur gear and the slipper clutch in his hands and should checked them, so is very improbable that the broken part...
  24. Thread: clutch

    by danyvw
    Replies
    68
    Views
    1,453

    Did you open the tranny? If the slipper clutch is...

    Did you open the tranny? If the slipper clutch is ok then could be a stripped input gear.
  25. Replies
    11
    Views
    737

    With the platinum header you won't have any leak...

    With the platinum header you won't have any leak at all.

    Sent from my LG-MS690 using Tapatalk
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4