Search:

Type: Posts; User: snowninja

Page 1 of 20 1 2 3 4

Search: Search took 0.32 seconds.

  1. Replies
    15
    Views
    258

    Thanks, will try to reach him via phone tomorrow....

    Thanks, will try to reach him via phone tomorrow. Need to get a replacement this week or will be down to one truck for next weekends racing.
  2. I would think you can run in 2wd, just remove the...

    I would think you can run in 2wd, just remove the center driveline
  3. Replies
    8
    Views
    205

    This always bothered me, still looking for fix.

    This always bothered me, still looking for fix.
  4. Replies
    15
    Views
    258

    pinned and not using 17mm adapters. I see they...

    pinned and not using 17mm adapters. I see they don't even offer pinned anymore, keyed could be design change to prevent breakage which leads me to believe this has happened more than we know. last...
  5. Replies
    15
    Views
    258

    The MIPS are 5mm. Having an extra 17% steel might...

    The MIPS are 5mm. Having an extra 17% steel might help.
  6. Replies
    15
    Views
    258

    Came off a small jump on my track and the wheel...

    Came off a small jump on my track and the wheel flew off..
  7. Replies
    15
    Views
    258

    Broken stub axle

    I broke an xtra duty mip axle today, second time. tthinking about the teckno's. Are they any better?
  8. Replies
    15
    Views
    226

    I like my mmp/2650 castle setup. Runs cool as a...

    I like my mmp/2650 castle setup. Runs cool as a cucumber
  9. Wow, you need an RC speedboat!

    Wow, you need an RC speedboat!
  10. Replies
    9
    Views
    157

    I've rounded a few of the stock ones so I just...

    I've rounded a few of the stock ones so I just swapped to aluminum. Seems like if Yuri keep the nuts tight the should be no problems with the stockers though
  11. Replies
    783
    Views
    53,637

    Yes. Looks low because the right rear hole on the...

    Yes. Looks low because the right rear hole on the body slid down over the post. http://img.tapatalk.com/d/14/07/01/e8uve2et.jpg
  12. Replies
    783
    Views
    53,637

    Beat the crap out of it on my backyard track....

    Beat the crap out of it on my backyard track. Tonight it gets an lcg chassis.
    http://img.tapatalk.com/d/14/07/01/meqa2u6a.jpg
    http://img.tapatalk.com/d/14/07/01/nuze5usa.jpg
  13. Replies
    26
    Views
    505

    lots of options available since I have upgraded...

    lots of options available since I have upgraded mine a few years ago. I have a novak ballistic 550 and a mm2650. my 2650 rarely reaches 150f but the mmp esc can get warm. I run on a home built track...
  14. Replies
    16
    Views
    313

    yes, the motor wires barely reached. good to know...

    yes, the motor wires barely reached. good to know the rx box mounts on the underside, thanks!
  15. Replies
    9
    Views
    175

    i prefer the aka endures on my track, loose dirt...

    i prefer the aka endures on my track, loose dirt with some clay. i have some proline gladiators and they fish tail too much
  16. Replies
    16
    Views
    313

    i've seen an ESC mounted up front with a custom...

    i've seen an ESC mounted up front with a custom mounting plate but not an rx box direct fit. if the RX box has holes on the underside then that might work.
  17. Replies
    16
    Views
    313

    i ordered a traxxas conversion kit and am looking...

    i ordered a traxxas conversion kit and am looking at the best way to fit my 2650/mmp. on my current setup i mounted a rustler/stampede rx box up front over the center driveline. is there room on the...
  18. Replies
    7
    Views
    267

    I use one and shortly after blew up the stock...

    I use one and shortly after blew up the stock servo. I put in a spectrum 6040 servo and running a castle 2650 and mmp so the external BEC was a requirement. Did a lot of experimenting to get it right.
  19. Replies
    16
    Views
    313

    Thanks. Do any of them beside kingheadz offer...

    Thanks. Do any of them beside kingheadz offer oversized bearings? Had too many days ended due to the undersized stocker
  20. Replies
    16
    Views
    313

    Thanks, Looks like the mount is $42. Sheesh..

    Thanks, Looks like the mount is $42. Sheesh..
  21. Replies
    16
    Views
    313

    lcg conversion

    I've had my hcg about 5 years and am thinking about converting using the traxxas lcg kit. Couple questions.

    Will my kings head motor mount work? If not which large bearing options are there?
    ...
  22. Replies
    12
    Views
    1,420

    ...and inexpensive. i also used a peice of...

    ...and inexpensive. i also used a peice of leftover lexan for the mount (also inexpensive!) :)
  23. Replies
    88
    Views
    12,442

    curious why you don't like this one.. is it the...

    curious why you don't like this one.. is it the price or something else?
  24. Thread: Blue lipo ??

    by snowninja
    Replies
    16
    Views
    1,558

    i used them as my first lipo's because they were...

    i used them as my first lipo's because they were $20 for a 2s/25C but i found after a while they got really flexible which may or may not be a bad thing but it just seemed a bit sketchy.. they are...
  25. Replies
    11
    Views
    2,081

    good thread, i hope the OP does not mind me...

    good thread, i hope the OP does not mind me asking an additional question related to q #1.

    is the novak 4s LVC the best one to use for running the EVX and LIPO's or is there a better one?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4