Search:

Type: Posts; User: El Bandito

Page 1 of 6 1 2 3 4

Search: Search took 0.27 seconds.

  1. Replies
    3
    Views
    233

    my battery right now hasnt peaked and currently...

    my battery right now hasnt peaked and currently it is at 8.44 volts. is that a problem?
  2. Replies
    3
    Views
    233

    2 cell lipo battery voltage question

    Ok i recently just purchased a 5000 mAh 2s 25c lipo battery. I was wondering what the voltage should be when you just pull it off the charger, when it is fully charged?

    Thank you all very much for...
  3. Replies
    4
    Views
    263

    5000 mAh 2s 25c lipo

    With this lipo battery, what kind of run times and speed can i expect? This battery will be used in a rustler with the VXL system.

    Thank you all for your help.
  4. Replies
    6
    Views
    1,908

    your shift hub is slipping on the shaft. you...

    your shift hub is slipping on the shaft. you either need to tighten the set screw that holds it to the shaft or replace the hub
  5. Replies
    8
    Views
    2,038

    i believe there is a roller on ebay with a carbon...

    i believe there is a roller on ebay with a carbon fiber chassis
  6. For Sale: Nitro 4-tec roller with upgrades! + More

    This car has the carbon fiber top plate, and rear brace. I also made a
    carbon fiber chassis, front stiffener, radio tray and shock tower. In
    addition to the carbon fiber parts, this car has...
  7. Replies
    3
    Views
    147

    I have a nitro 4 tec roller that im willing to...

    I have a nitro 4 tec roller that im willing to sell. It has the carbon fiber top plate and i have custom made a carbon fiber chassis for it as well. In addition to the carbon fiber goodies it has...
  8. Thread: look

    by El Bandito
    Replies
    6
    Views
    1,391

    He is talking about width not the diameter of the...

    He is talking about width not the diameter of the tire
  9. Thread: broken?

    by El Bandito
    Replies
    7
    Views
    873

    You need to tighten the set screw of the two...

    You need to tighten the set screw of the two speed hub to the rear shaft. that will fix your problems
  10. Replies
    3
    Views
    902

    My guess is that you dont even realize that it is...

    My guess is that you dont even realize that it is shifting into 2nd. because the 3.3 revs higher and quicker it becomes alot less noticable
  11. Replies
    17
    Views
    1,079

    like said before check your differentials and...

    like said before check your differentials and also check out the tweak of your tec
  12. Replies
    6
    Views
    907

    your two speed hub might be slipping on the...

    your two speed hub might be slipping on the shaft. take it apart and make sure it is tight and make sure that the set screw is on the flat
  13. Replies
    3
    Views
    895

    Tuned Resonator Pipe

    Hi all,

    I have a 4 tec with a 3.3 engine that i plan on racing. The track that ill be racing is fairly tight, there is only one straight that is about 30 yards long.

    Ive been looking in to the...
  14. Thread: Cornering

    by El Bandito
    Replies
    13
    Views
    475

    try locking or tightening your front diff. that...

    try locking or tightening your front diff. that will help pull it through the corners
  15. Replies
    6
    Views
    1,231

    adding a shim will lower the compression ratio....

    adding a shim will lower the compression ratio. With higher percentage of nitro you need to reduce the compression, and also you dont need a glow plug that burns all that hot.

    as far as adding a...
  16. Replies
    6
    Views
    954

    sounds like your low speed is set to lean. either...

    sounds like your low speed is set to lean. either that or your braking leankage needs to be adjusted.
  17. Replies
    3
    Views
    989

    I believe that the multi-shaft is the crank shaft...

    I believe that the multi-shaft is the crank shaft that you would use if you are going to put a traxxas engine in a non-traxxas car. So if your upgrading and its going in a traxxas car you would want...
  18. Replies
    11
    Views
    1,259

    OK i figured the problem out. The starter wheel...

    OK i figured the problem out. The starter wheel on the bump box was turning the motor over the wrong way. I switched polarities on the motor and it fired right up.

    Thanks for all the suggestions
  19. Replies
    7
    Views
    962

    2 speed drive hub

    What can i do to clean/ maintain my 2 speed? Im having trouble with it, and was wondering if there is anything that i could try to do to fix it.

    Thank You all very much
  20. Replies
    21
    Views
    509

    are you sure both your tires are spinning? is a...

    are you sure both your tires are spinning? is a drive shaft broken? is the screw thing in the white diff yoke still in place? the drive shaft could be spinning only one tire, but when you try it with...
  21. Def. go with the bump starter, and the traxxas...

    Def. go with the bump starter, and the traxxas backplate w/0 starter (you can just grind off the starter nub or buy the new crankshaft.) I dont know how this will work but have you tried putting...
  22. Thread: Sway bars

    by El Bandito
    Replies
    6
    Views
    877

    oh they make a difference... makes it less...

    oh they make a difference... makes it less squirly. try taking the rear shock tower and shock off. That will make more room
  23. Replies
    1
    Views
    906

    two speed transmission problem?

    When my 4 tec is going to shift into second gear it revs really high then i let off the throttle, then it shifts to second.

    Could i have installed the two speed unit on the shaft backwards? or is...
  24. no it came red red black black, i just switched...

    no it came red red black black, i just switched them to make the motors turn the other way
  25. ya it can start but i couldn't imagine that would...

    ya it can start but i couldn't imagine that would be good for your engine.
Results 1 to 25 of 143
Page 1 of 6 1 2 3 4