Search:

Type: Posts; User: Liam

Page 1 of 20 1 2 3 4

Search: Search took 0.34 seconds.

  1. Replies
    3
    Views
    110

    I would pull apart the tranny and replace the...

    I would pull apart the tranny and replace the plastic ones with metal ones (might already be metal depending on how old the rustler is. Other than that I'd recommend just letting your son upgrade...
  2. Thread: Maintenance....

    by Liam
    Replies
    45
    Views
    951

    I would check the bearings every 6 months or so...

    I would check the bearings every 6 months or so but if everything looked/worked fine I wouldn't see a reason to rebuild.
  3. Thread: Maintenance....

    by Liam
    Replies
    45
    Views
    951

    I would think so but I would wait for someone who...

    I would think so but I would wait for someone who actually owns one to confirm it.
  4. Thread: Maintenance....

    by Liam
    Replies
    45
    Views
    951

    I Highly doubt you would have to rebuild your Vxl...

    I Highly doubt you would have to rebuild your Vxl in a year unless you were running it very hard. I ran mine every 2-3 days for 3 years without ever rebuilding and I never had a problem
  5. Thread: Hex Hardware Set

    by Liam
    Replies
    14
    Views
    432

    Alright thanks, I'm guessing all the hardware for...

    Alright thanks, I'm guessing all the hardware for the stampede fits the rustler? (I couldn't find a definitive answer searching or googling).
  6. Thread: Hex Hardware Set

    by Liam
    Replies
    14
    Views
    432

    That one was sold the other items from the same...

    That one was sold the other items from the same seller only ship to USA.
  7. Thread: Hex Hardware Set

    by Liam
    Replies
    14
    Views
    432

    Problem is they don't ship to Canada.

    Problem is they don't ship to Canada.
  8. Replies
    13
    Views
    321

    Rustler's are great. They're fast out of the box,...

    Rustler's are great. They're fast out of the box, low maintenance and relatively inexpensive. Upgrade a few select parts and they're basically bulletproof too. I found them to be fun and good for all...
  9. Thread: Hex Hardware Set

    by Liam
    Replies
    14
    Views
    432

    Yeah, that's where I've mostly been looking....

    Yeah, that's where I've mostly been looking. Problem is most of them don't say whether or not they are traditional phillips type heads or are hex.
  10. Thread: Hex Hardware Set

    by Liam
    Replies
    14
    Views
    432

    Hex Hardware Set

    Anyone know where I can find a full hex hardware set? (Shipping to Canada)

    Thanks
  11. Replies
    33
    Views
    1,159

    When an 8.4v battery is fully charged it should...

    When an 8.4v battery is fully charged it should read around 9-9.1v.
  12. Replies
    33
    Views
    1,159

    There's no reason you should have to regear for...

    There's no reason you should have to regear for larger batteries. Higher mah doesn't result in more power (well, maybe slightly) it should definitely be exceeding the run time of the 3000's more than...
  13. Replies
    17
    Views
    504

    For more run time you'll want a battery with...

    For more run time you'll want a battery with higher mah rating (venom batteries aren't the greatest). A 7 cell (higher voltage battery) will give you more power. What esc and motor does your sons car...
  14. Replies
    15
    Views
    458

    I'm assuming you mean steel drive-shafts? Traxxas...

    I'm assuming you mean steel drive-shafts? Traxxas doesn't make any steel ones so you'll have to look at some dog-bones from FLM or some other aftermarket company.
  15. Replies
    7
    Views
    417

    Are you sure the slipper was reassembled properly...

    Are you sure the slipper was reassembled properly after you took the spur off?

    A general rule of thumb is 1/4 a turn, so tighten the nut all the way down and then loosen it 1/4 of a turn.
  16. The money has been sent but I can't send you my...

    The money has been sent but I can't send you my address because your inbox is full, notify me when you empty it.
  17. Replies
    11
    Views
    1,103

    Pm replied....

    Pm replied....
  18. Replies
    11
    Views
    1,103

    Pm sent......

    Pm sent......
  19. Replies
    11
    Views
    281

    What gearing are you running?

    What gearing are you running?
  20. Replies
    11
    Views
    1,103

    Will you ship to Canada?

    Will you ship to Canada?
  21. Replies
    8
    Views
    487

    Check both your front and rear diffs for any...

    Check both your front and rear diffs for any signs of a chipped tooth.
  22. Replies
    9
    Views
    675

    No, but look at how much torque/speed is put out...

    No, but look at how much torque/speed is put out at 6v. I'm fairly sure that's how much voltage most of the receivers that anyone would be using in a Rustler put out.
  23. Replies
    19
    Views
    3,080

    Nice looking truck :cool:. Really liking the...

    Nice looking truck :cool:. Really liking the body, was it airbrushed?
  24. Thread: 100 mph rustler

    by Liam
    Replies
    17
    Views
    3,146

    Unless you are ready to provide video proof of...

    Unless you are ready to provide video proof of this......don't bother posting about it.
    From what I know Sunnyhoustontx currently holds the record for the fastest Rustler at 90mph (correct me if I'm...
  25. Replies
    8
    Views
    1,725

    You might be able to squeeze them in but I...

    You might be able to squeeze them in but I wouldn't take the risk. Just look at some of the batteries on this http://www.promatchracing.com/site they're great quality and are reasonably priced as...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4