Search:

Type: Posts; User: Raptorpede

Page 1 of 20 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    2
    Views
    260

    Thanks for the suggestion I have a Savox servo in...

    Thanks for the suggestion I have a Savox servo in my Stampede and like it.
  2. Replies
    2
    Views
    260

    Servo on it's way out ?

    I noticed the Traxxas servo in my slash which is from my Stampede that wasa brushed xl-5 making it almost if not 3 years old and very well used ( stripped twice and rebuilt once a year ). It's...
  3. I get the shock caps and a front slash bumper I...

    I get the shock caps and a front slash bumper I have the RPM and it saved my bulkhed which is till plastic manytimes. Also metal castor bolcks are a good idea and lastly the strc hinge pin kit and...
  4. Replies
    6
    Views
    205

    It's a Pro-Line Body

    It's a Pro-Line Body
  5. Replies
    6
    Views
    205

    Thanks it's the only other body I found that was...

    Thanks it's the only other body I found that was .60 like my Raptor and this one I didn't crack the bed reaming the hole plus have added lexan doughnuts there.
  6. Replies
    6
    Views
    205

    New Body for the pede

    I got a new body to replace my Raptor which seen better days and had holes int plus I think this one is lower and I kept it simple but had to remove my receiver box and move some stuff around and...
  7. I do now have stronger rod ends now as I noticed...

    I do now have stronger rod ends now as I noticed it when putting on some new RPM ones.
  8. Stronger turnbuckles for a Pro-Tracked stampede

    I was wondering if anyone knows of a stronger link for a my truck as when changing my rod ends I noticed both my front camber links bent right t the end of the rod end and it is not a slight bend so...
  9. Replies
    10
    Views
    453

    On a warm day with warm soft compound race tires...

    On a warm day with warm soft compound race tires and slipper on the tighter side my 17.5 I can can get it off the ground abit but if I want wheelies I pull out the powered powered 3S stampede.
  10. Replies
    6
    Views
    129

    Did you spin the motor shaft to see if it spins...

    Did you spin the motor shaft to see if it spins normal or can you try the motor and esc in another car and see if it runs normal there.
  11. Thread: Best axles

    by Raptorpede
    Replies
    25
    Views
    573

    I am running the slash 4x4 rear shafts on my...

    I am running the slash 4x4 rear shafts on my stampede and 2wd slash and work great there the cheapest ones and been wearing very little and that is against a 3800 on 3S.
  12. Thread: Upgrades

    by Raptorpede
    Replies
    3
    Views
    226

    If you talking about the rear skid then yes go...

    If you talking about the rear skid then yes go RPM it is stronger and flat so it can slide over stuff and not get caught and it connects better. If your talking about the tabs that connect the...
  13. I find if the rear has too much play then it...

    I find if the rear has too much play then it makes it worse and also if the rear isn't adjusted even. Also I find when I ran stock arms with no toe in then it spins even more but I know I have cut...
  14. Replies
    10
    Views
    338

    Welcome I would go for the stock ultras with...

    Welcome

    I would go for the stock ultras with aluminum caps and tin shafts as the big bores are actually smaller in bore then the ultras also too the like the
    screw bottom of the ultra vs the...
  15. Replies
    2
    Views
    92

    Servo problems

    I think my servo may be going or something as when I ran my slash the servo got so hot that I couldn't touch it and got a temp gun and it was 100 degrees and needed 5 or 10 minutes to cool down and...
  16. I run 3S in my Stampede and never stripped a...

    I run 3S in my Stampede and never stripped a idler gear it also depends on your slipper setting plus how clean and lubed you keep your transmission . I have only stripped 2 one was on the Pro-Line...
  17. Replies
    1
    Views
    104

    Gearing help

    I put a Thunder Power 13.5T sensored motor in my slash and I not sure about gearing. I right now have it at 18/87 and I also have a 19,20,21,and 23 tooth pinion gears. It has a RPM transmission case...
  18. Replies
    12
    Views
    270

    I use monster jam mounts and they have held up...

    I use monster jam mounts and they have held up great for a few months of a castle 3800 on 3s and now there on my rubber RPM slash and still doing great mind you it's running 13.5 but still had it...
  19. Replies
    22
    Views
    382

    You put them on just like the stock 2wd shafts.

    You put them on just like the stock 2wd shafts.
  20. I just run the stock one with the RPM mount and...

    I just run the stock one with the RPM mount and the rubber tires and it been great he only thing that is bad is it sometimes readjusts itself or pop so I just use a string to hold it. This happens...
  21. Replies
    6
    Views
    201

    I also go with the 4x4 shafts and I been running...

    I also go with the 4x4 shafts and I been running them for 2 summers and run it alot and hard and they held up the a Castlle 3800 on 3S and show little to no wear, I like them so much I got them for...
  22. Replies
    7
    Views
    684

    I run a Kimbroug 124 and also ran it with the...

    I run a Kimbroug 124 and also ran it with the stock plastic geared servo and never had a problem. I still run it now but with a metal geared servo and it been great.
  23. I ran it in my truck when it had a vxl in it and...

    I ran it in my truck when it had a vxl in it and geared on the higher side I get 35 mintues. My brother has the same battery and he gets the same.
  24. Replies
    12
    Views
    783

    I may get aset for my slash as it running the...

    I may get aset for my slash as it running the rubber RPM castor blocks. Alo some for my stampede be nice.
  25. Replies
    22
    Views
    646

    Thanks for the susgestion but I'm looking at...

    Thanks for the susgestion but I'm looking at sensored motors because then it be smooth like the titan and won't cog at low speed and the extra smoothness.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4