Search:

Type: Posts; User: YZmoto

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    47
    Views
    3,536

    I am using a single Hitec 7995tg and as Pavment...

    I am using a single Hitec 7995tg and as Pavment said the servo saver is the limiting factor. In a high traction area or when the wheels are against an object the servo will move the steering arm, I...
  2. Replies
    52
    Views
    9,722

    I here you on that. I just got my plow build done...

    I here you on that. I just got my plow build done and want it to snow badly. I was out plowing mulch in the flower beds :)
  3. Thread: Buying used

    by YZmoto
    Replies
    19
    Views
    1,176

    I got a used 2.4ghz version for 300 shipped to my...

    I got a used 2.4ghz version for 300 shipped to my house. I disassembled, cleaned, greased bearings, dyed chassis, reassembled with a couple new parts totaling under $40 including a new dewalt 14.4v...
  4. Replies
    6
    Views
    385

    I never noticed a problem with mine until like...

    I never noticed a problem with mine until like you said about 125 ft away. It would do the exact same thing as yours. I am running lipos too. I think I will try installing caps this weekend. It is...
  5. Replies
    8
    Views
    936

    Igore- Thank you. I will plug it into the open...

    Igore- Thank you. I will plug it into the open steering spot for now.
    87 GN- I have a Castle Link I use from my erbe so I have already set it to 6.0 volts :D
  6. Replies
    8
    Views
    936

    Thank you for the link! That is good info. If I...

    Thank you for the link! That is good info.
    If I am to use the CCBEC to power everything and not just my steering servo where do I plug in the power to the receiver, since ch 5/batt is being...
  7. Replies
    8
    Views
    936

    Installing external BEC

    Does anybody know where to solder the leads of a Castle Creations BEC in order to power it from both the battery packs? I am running the stock ESC off of 2-2s lipos. I am going to use it to power my...
  8. Replies
    64
    Views
    9,617

    No caps here with 2.4 and no interference at all....

    No caps here with 2.4 and no interference at all.

    Reod12x2- Yes you could mount a stock motor back in the mount. All you have to do for the Dewalt motor is elongate the stock holes out a little...
  9. I put a LVC in mine. The only reason I used that...

    I put a LVC in mine. The only reason I used that instead of the LVA is because I wanted everything to remain waterproof. Just shoved the LVC in the reciever box. Works fantastic so far.

    87 GN-...
  10. Replies
    64
    Views
    9,617

    My 14.4 Dewalt motor will be here Monday :D so...

    My 14.4 Dewalt motor will be here Monday :D so thank you for the helpful tips and the pictures.
  11. Replies
    37
    Views
    3,127

    My turnigy 3s had the same problem. I cut the...

    My ******* 3s had the same problem. I cut the white foam padding back carefully and heated solder up. Then I pulled the wires back slightly so they were coming out the end.
  12. Replies
    55
    Views
    7,522

    Telnets, what pinion and spur are you running?

    Telnets, what pinion and spur are you running?
  13. Replies
    7
    Views
    914

    The usb plugs into the castle link, then the...

    The usb plugs into the castle link, then the castle link plugs into the wire from the esc that goes into the receiver.
  14. Thread: lipo care help

    by YZmoto
    Replies
    8
    Views
    863

    Connect the castle link to the esc and use the...

    Connect the castle link to the esc and use the software from Castles website to adjust it. http://www.castlecreations.com/downloads.html

    It is under the 'basic' tab i believe.
  15. Thread: 2.5 conversion

    by YZmoto
    Replies
    82
    Views
    2,225

    I am going though the exact same thing. All my...

    I am going though the exact same thing. All my parts came from a brand new erbe being parted out on ebay. I got everything shipped to my door for just over $100. Thats including everything to make my...
  16. Replies
    23
    Views
    2,094

    Maybe these(post 5)???...

    Maybe these(post 5)??? http://monster.traxxas.com/showthread.php?t=458846
  17. Replies
    54
    Views
    1,462

    Nice yamaha :D the ramp is sweet too

    Nice yamaha :D the ramp is sweet too
  18. Replies
    13
    Views
    387

    Kind of depends on what you plan on doing with it...

    Kind of depends on what you plan on doing with it i guess. I love my red dot but there are sometimes/places the 3.3 would have been absolutely perfect and and a more manageable power. Thats just me...
  19. Replies
    13
    Views
    346

    There was one left after i got mine. It must have...

    There was one left after i got mine. It must have went fast.
  20. Replies
    13
    Views
    346

    I snagged mine two weeks ago from superior...

    I snagged mine two weeks ago from superior hobbies. They were the only place that had any left. I love this engine:wub:
  21. Replies
    11
    Views
    423

    http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=L...

    http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXTTD2&P=7 He has these rims but dyed black.
  22. Replies
    27
    Views
    658

    ^ 2nd the front shots

    ^ 2nd the front shots
  23. Thread: mini revo

    by YZmoto
    Replies
    2
    Views
    353

    June seams to be the general consensus, but some...

    June seams to be the general consensus, but some say end of March(doubtful)
  24. Replies
    63
    Views
    6,170

    I like the look. Definitly have to drop the bell...

    I like the look. Definitly have to drop the bell some teeth.
  25. Replies
    9
    Views
    239

    ^ He probably just stacked the BB seal that came...

    ^ He probably just stacked the BB seal that came with the pipe on top of a SB seal. Atleast thats what i did for my red dot.
Results 1 to 25 of 40
Page 1 of 2 1 2