Search:

Type: Posts; User: cris

Page 1 of 4 1 2 3 4

Search: Search took 0.10 seconds.

  1. alright ill be getting me a body here before to...

    alright ill be getting me a body here before to long, great job!
  2. Replies
    28
    Views
    1,536

    yea i agree, it all depends on how you drive. iv...

    yea i agree, it all depends on how you drive. iv had mine for a year now and only broke 2 axle shafts, but that was my own fault. trying to crawl up a fork lift pallet lol. another time i got stuck...
  3. Thread: Summit Rock Racer

    by cris
    Replies
    69
    Views
    3,791

    that is a sweet looking summit. great job!

    that is a sweet looking summit. great job!
  4. Replies
    374
    Views
    22,103

    well this afternoon i sat down and re wired my...

    well this afternoon i sat down and re wired my fpv setup, installed the new spiro net antennas, and gave it a test drive. i got some new bumper mounts and double orange springs on the way. looking...
  5. :p~ this is going to be good. i been eye balling...

    :p~ this is going to be good. i been eye balling this body. maybe this will convince me to get it.
  6. Thread: Purex skid

    by cris
    Replies
    21
    Views
    776

    i made some out of some 0.30 lexan, they worked...

    i made some out of some 0.30 lexan, they worked ok but the grass would get stuck in the straps. i ended up tearing one off getting stuck in high grass lol....
  7. Replies
    7
    Views
    242

    yea on the front i just took the wheel off, the...

    yea on the front i just took the wheel off, the wheel hex, and the grub screw on the diff side and slid it out. on the rear i did the same thing but removed the tie rod and push rod for the shocks....
  8. Replies
    7
    Views
    242

    ok ill try that, thanks

    ok ill try that, thanks
  9. Replies
    7
    Views
    242

    axle shaft question

    hey guys, what is the best way to replace the outer shafts without taking the pivit balls off the arms. im
    looking at removing the lower skid plate in the front and pulling out the hinge pin? would...
  10. Thread: Is it worth it?

    by cris
    Replies
    51
    Views
    1,522

    i have mine locked in low gear permanently thanks...

    i have mine locked in low gear permanently thanks to a bread tie (burnt servo) lol. when ever i go out to the lake to fish, i take my summit and fpv gear out and explore the unknown. its fun!
  11. Replies
    10
    Views
    958

    you know actully that dont look bad at all! i...

    you know actully that dont look bad at all! i kinda like it. could that actully be done?
  12. Thread: i broke it

    by cris
    Replies
    17
    Views
    489

    yea the first time i broke the shaft was at the...

    yea the first time i broke the shaft was at the pin at the diff side. i redrilled 2 new holes oppisite from the broken holes and its been ok. that was the right rear.
  13. Thread: i broke it

    by cris
    Replies
    17
    Views
    489

    yea thats what i thought too. i might have...

    yea thats what i thought too. i might have weakend it this past weekend, when i got the truck stuck in a drainage pipe trying to back out lol.
  14. Thread: i broke it

    by cris
    Replies
    17
    Views
    489

    aint that the truth!

    aint that the truth!
  15. Thread: i broke it

    by cris
    Replies
    17
    Views
    489

    i broke it

    well i was doing some fpv driving, while driving i saw some pallets stacket up and thought i could crawl up.
    well that was a mistake. i got up on the first one, and then heard a snap. :O.o:i tried...
  16. Replies
    13
    Views
    545

    looks like you need some new bearings and a gear...

    looks like you need some new bearings and a gear set!
  17. Replies
    27
    Views
    948

    i think 6 and 7 in the picture is the motor.

    i think 6 and 7 in the picture is the motor.
  18. Thread: Body Shell

    by cris
    Replies
    19
    Views
    1,121

    the body i got was a e/maxx body. i thought it...

    the body i got was a e/maxx body. i thought it was a tmaxx body.
    http://i220.photobucket.com/albums/dd292/machine_024/2013-02-23_16-56-37_251_zpsac4a47cb.jpg
  19. Thread: Flying Summit

    by cris
    Replies
    22
    Views
    682

    thats totally cool. i got a friend that builds...

    thats totally cool. i got a friend that builds those and flys them. http://outfrontframes.com/wp/
  20. Thread: Body Shell

    by cris
    Replies
    19
    Views
    1,121

    the tmaxx body will fit, when i got my summit...

    the tmaxx body will fit, when i got my summit from a friend it had tmaxx body on it.
  21. well my summit is nothing compared to some of the...

    well my summit is nothing compared to some of the others posted here, but i am proud of what i got.
    mine is all stock including the traxxas nimh battery's only thing iv added was a fpv system....
  22. Replies
    30
    Views
    1,051

    when i did mine, i took out the motor to give me...

    when i did mine, i took out the motor to give me some room to get the plug out of the reviever box area, then just pulled the wire through the servo mount and out. some small needle nose help too.
  23. Thread: love my summit!!

    by cris
    Replies
    6
    Views
    322

    cool thanks jimmie, when it warms up ill go out...

    cool thanks jimmie, when it warms up ill go out and adjust it.
  24. when i got my summit that servo was bad, i bought...

    when i got my summit that servo was bad, i bought 2 china ones off ebay for 10$, they both lasted 20 minutes each lol. i said screw it and took the servo out completely and tied the lever in low...
  25. Thread: New order

    by cris
    Replies
    43
    Views
    1,710

    ebay has the dewalt motors.

    ebay has the dewalt motors.
Results 1 to 25 of 76
Page 1 of 4 1 2 3 4