Search:

Type: Posts; User: kdog

Page 1 of 6 1 2 3 4

Search: Search took 0.30 seconds.

  1. Replies
    13
    Views
    777

    i wash mine with soap and water. You can brush...

    i wash mine with soap and water. You can brush paint but its hard to not have brush strokes. If you have a hobby shop look for tranparent paint colors Tamiya makes them or mix some future with...
  2. Replies
    5
    Views
    1,001

    only thing i added to my install was that i added...

    only thing i added to my install was that i added some heatshrink over the axle cross bar thing incase the grub screw ever comes loose.
  3. a arm then a shock cap

    a arm then a shock cap
  4. Replies
    46
    Views
    3,231

    can the motor heat up from lower cell batts

    can the motor heat up from lower cell batts
  5. Replies
    29
    Views
    1,406

    I use a Thunder AC6 with no problems for my Lipos...

    I use a Thunder AC6 with no problems for my Lipos or NIMHs for 50 bucks you cant go wrong A buddy of mine went and bought a venom charger for like 130 bucks and its the same charger with different...
  6. I run that same battery on my 2400kv with no...

    I run that same battery on my 2400kv with no problems
  7. no heat issues but i do not have a temp gun I...

    no heat issues but i do not have a temp gun I love running it because its just fun!!!!!!!! Plus im running 1/8 proline knucklers on it.

    Thx
  8. I have had zero cogging with my 2400kv. It...

    I have had zero cogging with my 2400kv. It really zips on 3S and Im running 18/54.
  9. Replies
    35
    Views
    1,513

    THx for the coupon code!!

    THx for the coupon code!!
  10. Replies
    35
    Views
    1,513

    I keep seeing folks talk about using WD 40 on the...

    I keep seeing folks talk about using WD 40 on the bearings. Its a rust remover/ cleaner no t a replacement for iol or grease.

    I have used all types and Acer Goo has worked very good. Im going to...
  11. Thread: Soldering Iron

    by kdog
    Replies
    6
    Views
    428

    i use a weller sp80l wide tip does a great job

    i use a weller sp80l wide tip does a great job
  12. Thread: Slash 4x4 Gallery

    by kdog
    Replies
    751
    Views
    385,497

    Sticky: Here is mine SCT MMP 2400kv with 1/8 wheels...

    Here is mine SCT MMP 2400kv with 1/8 wheels Knuckler 2.0 tires and im using Losi Strike shocks. So far very happy. It a Truth body but I have a Raptor one on the way so ill post it again once its...
  13. Thread: 17mm hex adapter

    by kdog
    Replies
    9
    Views
    1,457

    i use the adaptors now first runs today and they...

    i use the adaptors now first runs today and they worked great
  14. Thread: king headz, lipo

    by kdog
    Replies
    10
    Views
    763

    The motor mount upgrades are for the use of a...

    The motor mount upgrades are for the use of a larger bearing. It lasts longer and causes less drivetrain issues. I do not think you can gear the same for 2s and 3s unless you keep it stock gearing.
  15. Replies
    8
    Views
    1,164

    Take out a loan!! j/k lol Go have fun and if...

    Take out a loan!! j/k lol Go have fun and if it breaks replace it with RPM parts. Once the center bearing starts goign get the Kingheadz or FLM motor mount. Till then have fun!!!!!!!!!!!!!!!!
  16. Thread: diff problems

    by kdog
    Replies
    16
    Views
    859

    i just made sure mine were slide all the way to...

    i just made sure mine were slide all the way to the sides no binding on mine
  17. Replies
    11
    Views
    488

    http://traxxas.com/support/models/electric/6808sla...

    http://traxxas.com/support/models/electric/6808slash4x4

    the exploded views are what you need
  18. Replies
    11
    Views
    488

    I just happened to change my rear dif oil last...

    I just happened to change my rear dif oil last night. I put in 15k oil to replace teh grease that comes stocks. I turned my left rear wheel and hte other side turns the oppisite direction. Same...
  19. Thread: New Slash 4x4

    by kdog
    Replies
    25
    Views
    809

    I run Teknos but a buddy runs x-duty MIPs with no...

    I run Teknos but a buddy runs x-duty MIPs with no problem and hes running a MM 2650.

    And I also spend what I want because its my stress relief I just run the crap out of my truck and hit things...
  20. Replies
    10
    Views
    773

    Castle's MMP + 2400kv then

    Castle's MMP + 2400kv then
  21. Replies
    10
    Views
    773

    I have both the 3800kv and 2400kv Castle systems...

    I have both the 3800kv and 2400kv Castle systems using the MMP. On 2S gear rright the 3800kv is what i would say is a good racer with tins of speed and no heat. the 2400kv on 3s is just plain fun...
  22. Thread: Life of the hobby

    by kdog
    Replies
    20
    Views
    705

    To me and my experience working on or fixing the...

    To me and my experience working on or fixing the truck is 50% of the draw for me. There is always something to fix, adjust, or just figget with.
  23. Replies
    21
    Views
    4,674

    I use ACER GOO. Its great i only change or repack...

    I use ACER GOO. Its great i only change or repack bearings aboutonce a month if Im bashing really hard.


    Also I use Moo slick and love it. Its the only thing I can find that repels the moon...
  24. Replies
    3
    Views
    275

    im in Iraq and i use the same Tower, A main,...

    im in Iraq and i use the same Tower, A main, LiguidRC. I have yet to find the one stop shopping. For big purchases i hit Tower because i joined the membership adn you save big on some items. Also...
  25. Replies
    11
    Views
    2,685

    ^^^^^ concur fully ^^^^^^^^^^^

    ^^^^^ concur fully ^^^^^^^^^^^
Results 1 to 25 of 147
Page 1 of 6 1 2 3 4