Search:

Type: Posts; User: mtc777

Page 1 of 12 1 2 3 4

Search: Search took 0.13 seconds.

  1. Take OFNA 1/12 wing instead of Traxxas one, it is...

    Take OFNA 1/12 wing instead of Traxxas one, it is bit bigger and it suits better...
    ...
  2. Didn`t measure them, but HR bodies have quite...

    Didn`t measure them, but HR bodies have quite bigger hole then stock, which results in a relatively big gap between body and piston.
  3. Its WT I`m talking about, not CTS....

    Its WT I`m talking about, not CTS....
  4. I had the same pistons in stock bodies and there...

    I had the same pistons in stock bodies and there was no issue, so I guess pistons are ok, but when I switched to HR bodies, every thickness beyond 3000 became a joke, it was like using no oil at all,...
  5. Yes, HR bodies has serious tolerance issues on...

    Yes, HR bodies has serious tolerance issues on the stock pistons...... and diff fluid and shock fluid are the same except for the thickness
  6. I use 3000 wt

    I use 3000 wt
  7. Replies
    4
    Views
    187

    One of the motor wire is broken or a connector...

    One of the motor wire is broken or a connector has bad contact. Try to locate where the bad spot is by moving the wires around while motor is running. If the wire is broken inside the motor can there...
  8. Check the bladder if it is properly aligned, it...

    Check the bladder if it is properly aligned, it can very easily slide away while screwing on the top of the shocks.
  9. But you can shorten the wires of the ESC, right ?...

    But you can shorten the wires of the ESC, right ?
    Now please explain the logic behind that.
  10. I just did....twice :)

    I just did....twice :)
  11. ...as I said

    ...as I said
  12. Overheated magnets would hardly cause cogging,...

    Overheated magnets would hardly cause cogging, the motor would just loose power. Cogging usually means that one wire is broken or connector has bad contact
  13. Replies
    14
    Views
    476

    Just my 2 cents: Learn to solder, if you plan to...

    Just my 2 cents: Learn to solder, if you plan to stick with this hobby. It is not expensive nor difficult, but benefits are huge...
  14. This is also VERY good charger, I would rather go...

    This is also VERY good charger, I would rather go that way....

    http://www.progressiverc.com/icharger-106b.html

    OR

    http://www.progressiverc.com/icharger-206b.html
  15. Thread: Brake issue

    by mtc777
    Replies
    1
    Views
    115

    Try recalibrating the esc or change it. Stock...

    Try recalibrating the esc or change it. Stock brakes suck anyway
  16. Replies
    6
    Views
    317

    You should post a link for more accurate answers,...

    You should post a link for more accurate answers, but basically what Jimmie said
  17. Replies
    8
    Views
    347

    Yes, but the voltage difference is too big to be...

    Yes, but the voltage difference is too big to be affected by difference in weight
  18. Replies
    8
    Views
    347

    I wonder why ...... 2x 7.2V = 14.4V 1x 7.4V =...

    I wonder why ......

    2x 7.2V = 14.4V
    1x 7.4V = 7.4V
  19. Thread: Axle shims?

    by mtc777
    Replies
    4
    Views
    180

    I won`t, I promise ....

    I won`t, I promise ....
  20. Replies
    12
    Views
    1,131

    What ???????

    What ???????
  21. Thread: Esc question

    by mtc777
    Replies
    9
    Views
    375

    It can be mounted flat if you swap ESC and rx...

    It can be mounted flat if you swap ESC and rx position like here:

    http://traxxas.com/forums/showthread.php?8974359-MTC-s-Mini-E-Revo
  22. Thread: Esc question

    by mtc777
    Replies
    9
    Views
    375

    Yes get Sv3, or Sv2 and waterproof it yourself if...

    Yes get Sv3, or Sv2 and waterproof it yourself if you want to save a few bucks
  23. http://www.nitrohouse.com/4mm-Bullet-Connector-90-...

    http://www.nitrohouse.com/4mm-Bullet-Connector-90-Degree-High-Effiecency-Male-Plug-4_p_2404.html
  24. Replies
    9
    Views
    552

    Does the servo itself turn for the same angle...

    Does the servo itself turn for the same angle each direction ?
  25. Thread: Tire settings

    by mtc777
    Replies
    3
    Views
    200

    Adjust the pillow balls

    Adjust the pillow balls
Results 1 to 25 of 295
Page 1 of 12 1 2 3 4