Search:

good turnout 2wd buggy, 4x4 sc, 2wd sc. we wrapped up about 10pm 2 qualifiers + main race. so much of a turn out for 2wd short course trucks that there was a A and B main. if your in the area stop...

4/17/12 is when racing starts 5pm-? jump, carpet, lap counting system, pit area the whole 9 yards. click here for some pics http://www.ultimaterchobbyshop.com/apps/photos/album?albumid=13220453 its...

for the record the black trans will work with the 4907 chassis. i had to extend the driveshafts but i already had extra long half shafts that i just cut down. and so far the trans is holding up...

nice ride, i like those W bodys. i suggest against the 20's-they rub and at 16 money is tight... well it was for me back then, so if you get a flat or break a rim it will cost a pretty penny. also...

cool thanks alot jimmie

thanks for the info. i was looking to go the brushed route because i figured it would be cheaper than a brushless setup. i like running it indoors and i think the brushless will be too much power...

just picked up an e revo last week its got a 380 titan. its neat but i think the motor has to work too hard run times are not very much and motor too hot with stock gearing. i was thinking of...

yeah there good trucks as long as you keep up the maintainance. the transmission 4l60E isn't the strongest in the world and yes the 3-4 clutch is prone to getting wasted. the 4.3l is a good engine,...

lets see whats better vanilla or chocolate?! lol i like nitro when i bash because the 3.3 has the power to go over or through just about anything. but electric is better for me to race because you...

the revo does use a pretty sweet chassis but trading a brand new rig for a used one? big block or not i don't think its a good trade. that would be like trading in your 2012 f150/silverado/ram-you...

i run nimh, nicad is very cheap but lower amp hour ratings-MAH. when a nicad is run the discarge voltage gradually decreases untill the battery is discharged. on a graph this would look like a side...

nitro attracts moisture which can lead to rust. after run oil protects the bare metal from moisture and only takes 10 seconds to do. i run out of fuel and fill the carb up with after run oil and...

thanks for all the input guys. due to lack of off road race tracks in my area my maxx is just a basher so durability is more important than adjustability- for now.

now when you guys say about the bearings wearing out how long do they last? also does it give you any warning noise, loose, or do they just lock/explode? whose bearings should i use for good...

i was just curious if anyone has this on there rig and how they liked it. thinking of going with rpm arms all around and wanted to put this on the back but i always like to read the reviews first....

yeah those out-laws are terrible, they force you to do things against your will at gun point! lol

I'm not sure i would agree with painting the head or crankcase. These engines are air cooled and the paint may act like insulation and keep head in and not allow proper heat dissapation. i would...

i have used a pull start, ez start, and a bump box. the ez start is easy to use but eats stick packs using a glow ignitor helps but defeats the purpose. if you have a good tune and a good glow plug...

stick with rubbers for general bashing. and run foams if you race. i would run a medium compound because its a good balance of grip and wear

i disagree about "odd ball" scale sizes. in the past different doesn't last long. look at the 1/6 traxxas monster buggy, the kyosho super 10, and the hpi super nitro. yes traxxas is growing...

i run nimhs in my rig because i don't want the extra expense of converting to lipo. i can run 8.5-11 minutes on 2000mah. also i don't run it till it stops i will pull it off the track when the...

i have the 2.5 plastic pipe on my 3.3 it works but its most likely costing me power. i bought a 2.5/3.3 conversion kit to put a 3.3 in my 4910 pro .15 maxx and that is the pipe they include in the...

put the forward only kit in and eliminate reverse. i have one in my rig and have no intentions of putting reverse back in. puts the power down smother, less rotating weight, simplifies transmission...

if it has a fuel filter, replace or clean it, replace the glow plug, reset the carb to factory needle settings and go from there. also remember that the carb is only made from plastic and its...

yes its the other way around smaller spur= more speed decreased torque output, larger spur=less speed more torque output. larger pinion=more speed decrease torque, smaller pinion=less speed more...