Search:

Type: Posts; User: PowerToTheMaxx

Page 1 of 20 1 2 3 4

Search: Search took 0.37 seconds.

  1. Replies
    20
    Views
    397

    That or get a front end wing, either get one off...

    That or get a front end wing, either get one off a old or new scrap body, or modify one from a 1/10 scale 190mm street car. They are about the same size. Also, a wheelie bar will help force the front...
  2. Replies
    6
    Views
    121

    I have 5 air filter elements and the oil. How do...

    I have 5 air filter elements and the oil. How do I clean them again?

    Proline also doesnt list its 2.8 sand paw tires for jato. There a reason for that? And u guys have any options on those or is...
  3. Replies
    6
    Views
    121

    Ya, just fresh water lake. I figured with the...

    Ya, just fresh water lake. I figured with the oil. Hmmm. I figure sand tires are a must for rear, what about front? Should stock or dirt hawgs be fine? Maybe some rustler front tires, although I...
  4. Replies
    6
    Views
    121

    Sand Options

    I'm looking at taking my jato to the beach and I was wondering what you guys think about that. My E-maxx does well on sand with paddle tires, but ive never run nitro on sand before and I was...
  5. Replies
    60
    Views
    2,528

    Hmm. Ya, KD stuff doesnt favor motor mount...

    Hmm. Ya, KD stuff doesnt favor motor mount covers. Can't wait to see what your eBay guy comes up with
  6. Thread: Ouch!

    by PowerToTheMaxx
    Replies
    6
    Views
    409

    I run rpm bulks with UE towers. Seems to be...

    I run rpm bulks with UE towers. Seems to be holding up fine but I havnt run my truck much with this setup. I strongly recomemd UE towers because they are the strongest on the marked and have many...
  7. Replies
    31
    Views
    539

    Which is better, the ths pipe or one of the...

    Which is better, the ths pipe or one of the Traxxas pipes? Also, is it a direct fit or is it much longer than the stock plastic one. I want to ditch the plastic pipe and get a good pipe that works...
  8. Replies
    5
    Views
    193

    Be careful with too much line and space... If you...

    Be careful with too much line and space... If you have too long of a line, the pressure from the pump (muffler) won't feed the fuel into the carb at a high enough rate and your engine won't run well
  9. Replies
    3
    Views
    184

    s far as bearings, Acer, avid, and Boca make...

    s far as bearings, Acer, avid, and Boca make pretty much all types of bearing, just measure the I.d. of the wheel and use that for the o.d. of the bearing.
  10. Replies
    11
    Views
    369

    Welcome to the forum. And yes, that or my 4...

    Welcome to the forum. And yes, that or my 4 stroke nitro... Except it has no compression and I can't find the wrench to get it off the plane :O.o:
  11. Replies
    3
    Views
    107

    Ez start? Could be something bad there. Could be...

    Ez start? Could be something bad there. Could be there was so much gunk in the motor the oil wasn't enough. If the flywheel turns, great. If not, I'd try putting a bunch of WD in thru the glow hole...
  12. Ya, I'd go to 17 or 15 tooth pinions, will save...

    Ya, I'd go to 17 or 15 tooth pinions, will save motors in the long run. +1 on those temps, but I would also check the gear mesh. If one pinion is to tight against the spur, that motor will run hot....
  13. Replies
    60
    Views
    2,528

    Also, on your hinge pins, most people use...

    Also, on your hinge pins, most people use lunsford pins on the bottom or stock because of steering problems. However, if you get the end of the pin and grind down the head so it clears the steering...
  14. Replies
    60
    Views
    2,528

    Really nice project. Can't wait to see it done. U...

    Really nice project. Can't wait to see it done. U put any thought towards a body for either of them?
  15. Replies
    5
    Views
    193

    Mine goes from the tank around the outside of the...

    Mine goes from the tank around the outside of the aircleaner and in the back of the carb, zip tied around the air cleaner to keep it out of the gears. Its around 6" long, and for the most part I can...
  16. Cool, Thats exactly what I was looking for. I...

    Cool, Thats exactly what I was looking for. I ended up making a few with a drill press and 1/4" square aluminum stock, so after I kill those or get tired of 0 degrees anti-squat, Ill look into one of...
  17. Replies
    3
    Views
    110

    Or... Just for kicks, you can go here. ...

    Or...

    Just for kicks, you can go here.

    Acer bearings, just a third option. I have some avid bearings but all three companies make good stuff.

    http://www.acerracing.com/
  18. Replies
    7
    Views
    263

    Also, to prevent that happening again you can get...

    Also, to prevent that happening again you can get ST Racing aluminum knuckles for Revo. Theyre a little more expensive but ive run mine for nearly two years now and havnt had a single issue or popped...
  19. Replies
    52
    Views
    3,154

    Been really busy recently, but finally got...

    Been really busy recently, but finally got everything back together and got some dirt on it.

    I did lose a drive shaft and cup, my fault for not using springs or thread lock. I gave up on trying...
  20. Thats the plan now, seems like new era has one...

    Thats the plan now, seems like new era has one but should be easy to make myself. Anyone else have problems with this? I broke two within two hours of running, one I slid into a car not going very...
  21. Anti-Squat/Suspension Pin Retainer question

    Ok, so Ive broke two Traxxas 5559 suspension pin retainers and I was wondering if anyone makes a aluminum or at least upgraded piece.

    Or is there something I can do to strengthen it myself.
    ...
  22. I just worried I'm gonna over discharge it but I...

    I just worried I'm gonna over discharge it but I have also used lipo packs
  23. Replies
    2
    Views
    159

    Lots of guys on the other branches of the forum...

    Lots of guys on the other branches of the forum arnt usually happy with their integy stuff. Most people complain that it isnt near as strong as many other brands like UE or FLM or Hot Racing.
    ...
  24. Replies
    7
    Views
    220

    Will 190mm street car bodies fit the jato well?...

    Will 190mm street car bodies fit the jato well? I'm looking at getting one, lots of "keel" bodies there if they do
  25. I use a 8.4v battery held in with a Velcro strap...

    I use a 8.4v battery held in with a Velcro strap and cause its Traxxas plug, I use the Traxxas to taymia thing as well. So far no wiring issues and as my friend says, "those 8.4v nimh on ez-start are...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4