Search:

Type: Posts; User: moody03svt

Search: Search took 0.22 seconds.

  1. Replies
    36
    Views
    2,313

    Ok so far truck runs great and still seems pretty...

    Ok so far truck runs great and still seems pretty stable to me. But I was thinking, I think I left the factory shim in between the hub carrier and the CVD where if I moved that shim to the outside...
  2. So this helps for that rubbing but what about my...

    So this helps for that rubbing but what about my MIP X-Duty ball cups near the hub rubbing on the hub carrier when the suspension is fully extended. I had to install fuel tube to reduce the travel of...
  3. Replies
    13
    Views
    2,334

    I know old post but thought I would bring up this...

    I know old post but thought I would bring up this same slight rubbing on the rear. I bought the MIP X-Duty CVDs for my 4x4 VXL Pede. I had to install some fuel tube in the shock to stop it from fully...
  4. Replies
    2
    Views
    319

    I think I understand what you mean and you don't...

    I think I understand what you mean and you don't need anything once you get the truck it is ready to go. All the tools needed are included with the kit (although they may not be the easiest tools to...
  5. Replies
    4
    Views
    264

    If you are referring to the motor then I would...

    If you are referring to the motor then I would recommend the Integy Heat Sink and Fan (there is also a double fan as well.) But for just the ESC I am using the Traxxas one.
  6. Replies
    484
    Views
    22,236

    No parts broken today but my friend broke some.

    No parts broken today but my friend broke some.
  7. Thanks all

    Thanks all
  8. Replies
    36
    Views
    2,313

    Those definitely have a smaller looking cup that...

    Those definitely have a smaller looking cup that looks like should handle larger angle without rubbing. I wonder how the hex will hold up compared to multiple splines like the MIP.
  9. Replies
    36
    Views
    2,313

    Good thought on hub carrier, it does have two...

    Good thought on hub carrier, it does have two holes but right now its in the bottom one from factory. if I move the arm to the upper hole then it would only make the angle worse. and I definitely did...
  10. Replies
    36
    Views
    2,313

    I appreciate your point of view, sometimes people...

    I appreciate your point of view, sometimes people will be smart mouthed and come back with "well that is what you pay for when you play hard." I agree with what you said and see that MIP did that. I...
  11. Replies
    36
    Views
    2,313

    ok installed fuel line inside the shocks....

    ok installed fuel line inside the shocks. definitely lost some suspension travel, pretty much the tires don't drop at all when I pick it up off the ground. I have yet to drive it though to see how it...
  12. Replies
    36
    Views
    2,313

    hey Baldy, Good Info, I have been having a hard...

    hey Baldy,
    Good Info, I have been having a hard time with this too. I want the durability but the MIP X-Duty's due have some slack in them and they do rattle. Combined that with they bind a bit when...
  13. Replies
    36
    Views
    2,313

    I just installed the MIP X-Duty CVDs on my 4x4...

    I just installed the MIP X-Duty CVDs on my 4x4 Stampede and now when my tires full droop or extend I get binding. so I need some of these internal limiters. I was not sure if they are included in the...
  14. ah now this makes sense. Because the large ring...

    ah now this makes sense. Because the large ring and pinion gears looked good and did not seem to have anything on them but grease and no signs of wear I was a bit unsure. But I didn't go far enough....
  15. Replies
    484
    Views
    22,236

    Thanks for info, I think. I will check over the...

    Thanks for info, I think. I will check over the manual again. Is the ring gear casing the same as the rear diff cover? I removed the cover which exposed the ring gears and there was grease all over...
  16. So if it is normal then why the binding I wonder....

    So if it is normal then why the binding I wonder. It was definitely coming from rear end. I checked all 4 bearings on axles and the diff bearing felt good. The only thing left was the gears or a...
  17. Replies
    484
    Views
    22,236

    I don't think I broke anything but I opened my...

    I don't think I broke anything but I opened my rear diff and found nothing but sludge, nothing leak or dripped out. Don't know if that is normal. I should probably check the front diff...
  18. New Stampede VXL 4x4 - 2S Lipo - 3 packs and open rear diff no fluid

    Is this normal? I ran 3-4 2S Lipo packs through truck and then was thoroughly cleaning it and decided to take off rear diff because it felt like it was binding. Took cover off and no fluid came out....
Results 1 to 18 of 18