Search:

Type: Posts; User: NorSlash

Page 1 of 3 1 2 3

Search: Search took 0.06 seconds.

  1. Replies
    3
    Views
    521

    Put it under. You probably need some 15mm screws...

    Put it under. You probably need some 15mm screws instead of the 12mm stock ones. I cut along the markings and it fit perfect.
  2. I still find the hot glue solution the best, as...

    I still find the hot glue solution the best, as there is NO added mass to the shaft, so no vobble, and it's a perfect fit. I'd think anything you actually fix on the shaft would need to be properly...
  3. I just used hot glue up front. I've posted that...

    I just used hot glue up front. I've posted that solution on this forum before.

    Vaseline on the shaft, then a good blob of hot glue in the tunnel, then pop the lid on. Makes a perfect seal.
  4. Replies
    10
    Views
    620

    70 weight on a cold day... How heavy is you...

    70 weight on a cold day... How heavy is you truck, and what springs?

    Sounds overdamped to be honest, but for really rough stuff I guess it's all right.
  5. Replies
    2
    Views
    338

    I always fumble that bit. It's much easier if you...

    I always fumble that bit. It's much easier if you have a friend that can jiggle the rear wheels a little while you keep everything aligned. It's one of those "I wish I was an octopus" jobs... :)
  6. Replies
    8
    Views
    717

    Dirt in the bearing caused it. The bearing...

    Dirt in the bearing caused it. The bearing failed, meking it spin on the plastic. This creates heat, which melts the plastic.
  7. Replies
    11
    Views
    482

    Check the bearings on the 'stuck' side. The diff...

    Check the bearings on the 'stuck' side. The diff is supposed to turn the opposite wheel, as long as the driveline is restricted. Usually there will be more resistance in the motor than the opposite...
  8. Replies
    8
    Views
    779

    I run 60wt in the rear, with the stock Pro-Line...

    I run 60wt in the rear, with the stock Pro-Line springs, I think they are the yellow ones. I have the pro_line spring kit for the shocks, so I'll experiment a bit.

    How would you say the primary vs...
  9. Thread: diff problems

    by NorSlash
    Replies
    16
    Views
    853

    Are the gears the right way? Did you clean all...

    Are the gears the right way?
    Did you clean all the parts thoroughly so thereŠs no dirt causing the binding?
    Are you sure you align everything properly?

    Just throwing stuff out here. I know it's...
  10. Replies
    8
    Views
    779

    The shocks are perfectly fine, and rebound nicely...

    The shocks are perfectly fine, and rebound nicely when compressed 'manually'.

    Ok, I'll try to get some thicker fluid in there. I'm already pretty oversteered, so I'd rather go softer than stiffer...
  11. Replies
    8
    Views
    779

    Bouncy rear end

    I got my Pro-Line shocks, and set them up per Slayden's setup thread. I used stock

    When in really rough terrain the rear bounce a little, and the car feels a little oversteery, especially off the...
  12. Thread: diff problems

    by NorSlash
    Replies
    16
    Views
    853

    Well, it's supposed to fit with the seal in...

    Well, it's supposed to fit with the seal in there... I'd say something is wrong somewhere. You are sure you don't already have a blue seal in there?
  13. Thread: diff problems

    by NorSlash
    Replies
    16
    Views
    853

    The sideplates that the planetary gears and axle...

    The sideplates that the planetary gears and axle mount to is upside down. Make sure the dimples are facing you when you reassemble. Check the exploded views if you are unsure.
  14. Replies
    7
    Views
    301

    Truck comes alive with 3S though. I recommend...

    Truck comes alive with 3S though. I recommend getting one just to try it out. I'm not going back, that's for sure.
  15. Replies
    30
    Views
    1,646

    It's weird that different people have such...

    It's weird that different people have such different view on the same product.

    I wtill think that it may be temperature related. I will get another Pro-Line body but not run it until it gets...
  16. Replies
    5
    Views
    378

    I let it airdry, then do a complete teardown...

    I let it airdry, then do a complete teardown every few weeks, depending on runtime.

    If it's dirty I hose it down before taking it inside.
  17. Replies
    30
    Views
    1,646

    I don't think it was frozen. It was a few degrees...

    I don't think it was frozen. It was a few degrees above freezing when I took her out today. But yeah, I guess the cold makes the lexan more brittle.
  18. Replies
    30
    Views
    1,646

    Proline bodies

    I recently bought the Pro-Line Baja Bug body for my Slash 4x4. Looks awesome, and I love it.

    Then I went for a run. One pack on icy roads and grass. Flipped it once, and didn't think more of it...
  19. And did you ever have to refill a non-damaged...

    And did you ever have to refill a non-damaged damper? I guess not.
  20. It will be plenty fast with 13/54 for snow. I'd...

    It will be plenty fast with 13/54 for snow. I'd say it is plenty fast for almost anything with 3S and 13/54.
  21. But unless the shocks are leaking you shouldn't...

    But unless the shocks are leaking you shouldn't have to top them up.

    Check your suspension for binding. Make sure everything is smooth and flappy with the shocks off. Also inspect the shocks for...
  22. Replies
    33
    Views
    664

    Yes, the nut and spring is essential for the...

    Yes, the nut and spring is essential for the slipper to work. If you don't have that I do not know how your truck even runs.
  23. Thread: Shock fluid

    by NorSlash
    Replies
    8
    Views
    399

    I also use the Pro-Line Powerstrokes. 60wt rear,...

    I also use the Pro-Line Powerstrokes. 60wt rear, 50wt front, dual-hole piston and stock springs. The ride is sweet.
  24. Thread: Blew it up!

    by NorSlash
    Replies
    6
    Views
    407

    There's an alu centerdiff housing? Where can I...

    There's an alu centerdiff housing? Where can I get that?
  25. Thread: Shock fluid

    by NorSlash
    Replies
    8
    Views
    399

    Depends on your spring setup and vehicle weight,...

    Depends on your spring setup and vehicle weight, and piston valving. So, there's no correct answer to that one. Also depends on the surface and driving style.

    I use 60wt rear, 50wt front with...
Results 1 to 25 of 54
Page 1 of 3 1 2 3