Search:

Type: Posts; User: seh2000

Page 1 of 2 1 2

Search: Search took 0.11 seconds.

  1. Hi! @jaman: Rear pillow balls checked - they...

    Hi!

    @jaman:
    Rear pillow balls checked - they appear not to be too loose nor too tight.
    Rear toe links are in the middle hole.
    I will adjust the Pre load to see the difference.
    Its just that...
  2. Hi... Its not only when the Summit starts or we...

    Hi...
    Its not only when the Summit starts or we are giving throttle is is basically all the time, when driving the rear parts is much lower than the front part, as the 1st photo illustrates.
    No...
  3. 2nd Drive - sagging/hanging rear (suspension) + T-Bone

    Hi all,

    As some of you might recall we got a new Summit in April, but during our 1st and till now our only drive we broke the front right A-arm.

    We got the A a few weeks ago as well from T-Bone...
  4. Replies
    24
    Views
    916

    @jamann, Hmm - actually we are very close to...

    @jamann,

    Hmm - actually we are very close to the sea, but here is very dry as not much rain, but lots of sun. So the wet spots dries pretty fast.
    There is a sea water canal just next to where we...
  5. Replies
    24
    Views
    916

    @ksb51rl, Yes, I now understand that one...

    @ksb51rl,

    Yes, I now understand that one really do not want any oils and/or grease in the area for the pillow ball.
    Guess, if one oil it then there will be more dirt and as the pillow ball is of...
  6. Thread: wet tyre foams

    by seh2000
    Replies
    16
    Views
    762

    Thanks - Steen

    Thanks - Steen
  7. Thread: wet tyre foams

    by seh2000
    Replies
    16
    Views
    762

    LoL - 2mm drill bits I got so i'll start...

    LoL - 2mm drill bits I got so i'll start drilling...

    thanks - Steen
  8. Replies
    24
    Views
    916

    YOHUUUUU, had never found it without your...

    YOHUUUUU, had never found it without your "hint"!!!!
    Arm is now out...
    Question what oil/grease shall we use when we out the pillow? ball back in?
  9. Replies
    24
    Views
    916

    we are not too sure, we been looking the video(s)...

    we are not too sure, we been looking the video(s) we took, but no clue.
    There are lots of small and big stones/rocks, but we cannot see if we hit something or remember.
    We drive in same area with...
  10. Replies
    24
    Views
    916

    @ jungletreker - difficult to say, but most...

    @ jungletreker - difficult to say, but most likely you are right. I am still trying to figure out how to get the arm seperated from the pivot at the wheel side...
  11. Hi mattinpa - thanks to you and jimmie :o) Now...

    Hi mattinpa - thanks to you and jimmie :o)

    Now we just need to fix the broken a-arm...


    Cheers Steen
  12. Yep jungletreker, LoL, unfortunately we did...

    Yep jungletreker,

    LoL, unfortunately we did not take too many pictures, next time more as the area is rather large with different types soil...


    Cheers Steen
  13. Replies
    11
    Views
    918

    Not all shipped with the "new" ESC got the...

    Not all shipped with the "new" ESC got the addendum in the box.
    Like ours which we got two weeks back had the "new" ESC, but no paper.
  14. Thread: wet tyre foams

    by seh2000
    Replies
    16
    Views
    762

    To everybody - Thanks!!!

    To everybody - Thanks!!!
  15. Thread: wet tyre foams

    by seh2000
    Replies
    16
    Views
    762

    summit thing: what size of drill bit you used? I...

    summit thing: what size of drill bit you used? I think I will do as you...
  16. Replies
    24
    Views
    916

    Hi jimmie: I will try to disassemble...

    Hi jimmie:

    I will try to disassemble tomorrow...thanks...let you know how it went.
  17. Replies
    24
    Views
    916

    @snowslider: Cool - thanks. I'll see if we can...

    @snowslider:
    Cool - thanks. I'll see if we can find here...

    @ksb51rl
    I have not yet removed the. I can see some marks from driving over small stones/rocks. It looks like it simple snapped in two...
  18. Replies
    24
    Views
    916

    Thanks!! Since I am to replace the arm I will...

    Thanks!!

    Since I am to replace the arm I will either before or at same time use some paint.

    How about nail polish?
  19. Replies
    24
    Views
    916

    Hi ksb51rl, I agree it looks like, but we had...

    Hi ksb51rl,

    I agree it looks like, but we had the ESC in the training mode so speed not that high.
    There are small rocks here and there, some dry deep tire tracks from "real" cars/trucks we drove...
  20. Replies
    4
    Views
    277

    Hi jimmie: Again thanks! Its really nice to be...

    Hi jimmie:
    Again thanks! Its really nice to be "member" here!
    I'll try to do a small "adjustment"...

    Hi krallopian:
    Yes, we done the same or we lift up the summit, but I will also see if as...
  21. Replies
    24
    Views
    916

    Hi jimmie: Thanks :O) (I guess - LoL) just put...

    Hi jimmie:
    Thanks :O) (I guess - LoL) just put in an order for a new set of arms (both the left and the right) expect them in 10 days...
    Properly I should have ordered the rear too - maybe??

    Hi...
  22. Replies
    4
    Views
    277

    Stock Tires and Steering Servo noise...

    Hi!

    The stock tires on our new Summit gives the impression of being "sticky" is that normal?
    Is there a better set of tires then the stock tires the Summit comes with that can be recommended for...
  23. Replies
    24
    Views
    916

    Suspension Arm broken after 1st drive

    Hi,

    Decided to split my 1st drive post into two posts.


    We discovered our new Summit after our 1st drive had sustained a severe damage - to our surprise, as we used the same track with our non...
  24. Thread: wet tyre foams

    by seh2000
    Replies
    16
    Views
    762

    Thanks snowslider and jamann!

    Thanks snowslider and jamann!
  25. Thread: wet tyre foams

    by seh2000
    Replies
    16
    Views
    762

    Sorry to bump in, but maxi single the holes...

    Sorry to bump in, but maxi single the holes should the be in the middle of the tires or on the sides of the tires?
    What method the best to "cut" the holes? Like using a drill bit?

    Thanks - Steen
Results 1 to 25 of 38
Page 1 of 2 1 2