Search:

Type: Posts; User: GASSHEAD

Page 1 of 20 1 2 3 4

Search: Search took 0.10 seconds.

  1. Thread: gearing?

    by GASSHEAD
    Replies
    11
    Views
    260

    itl be mostly a track basher, just something to...

    itl be mostly a track basher, just something to "toy" around with
  2. try putting foam on the underside of ur batter...

    try putting foam on the underside of ur batter holddown, so it is a tight fit when you go to put the clip through, that should be more than enough.
  3. Replies
    15
    Views
    1,299

    just set the needles to stock and re-tune from...

    just set the needles to stock and re-tune from there...4.5 out on HSN, 2.5 out LSN, and a 1mm gap for the idle on the slider in the carb
  4. Replies
    89
    Views
    1,347

    al i want for x-mas is for my family to be cival...

    al i want for x-mas is for my family to be cival towards each other
  5. Replies
    13
    Views
    298

    pop out one of the bushings and measure the OD...

    pop out one of the bushings and measure the OD with some calapers, most bearings are sold in MM dementions
  6. Replies
    11
    Views
    433

    not really, the lazer removal tech is advancing...

    not really, the lazer removal tech is advancing every day. if he really wqants it gone, he has plenty of options...cover up, skin removal( accually cut the tat out), or lazer removal
  7. Thread: gearing?

    by GASSHEAD
    Replies
    11
    Views
    260

    come on guys, does anyone have a good starting...

    come on guys, does anyone have a good starting point?
  8. Thread: gearing?

    by GASSHEAD
    Replies
    11
    Views
    260

    gearing?

    i have a novak ss+ 5800 combo, what would be good gearing for my pede, running 2.2 bowties and 7 cells, its also jangafied
  9. Replies
    83
    Views
    12,235

    no, only new era

    no, only new era
  10. Replies
    15
    Views
    557

    yeah make them so that go down, that way all the...

    yeah make them so that go down, that way all the crud can just blow over, or the water can run off. i also like the way the servo wires were routed
  11. Replies
    31
    Views
    399

    y not try a crawler motor, 45 turn maby a 55...

    y not try a crawler motor, 45 turn maby a 55 turn, using a similar gearing
  12. Replies
    33
    Views
    503

    uhh, this year im not thankful for very much. my...

    uhh, this year im not thankful for very much. my life is kinda falling apart around me, first my mom lost her job, then the GF left me, now my grades are falling in my jr year of college


    my...
  13. Replies
    2
    Views
    216

    if its the E-REVO the tranny stays stock. if its...

    if its the E-REVO the tranny stays stock. if its a Nitro Revo conversionits locked into second with a few screws. most are useing a wide ratio kit when this is done
  14. Replies
    14
    Views
    882

    well i got it to the driveable stage. running a...

    well i got it to the driveable stage. running a 15t motor 8 cell and a super rooster esc. made a topplate out of CF to stiffen it up. still got some more odds and ends to finish but she is almost...
  15. Replies
    12
    Views
    665

    ive always had great luck with shoe goo. just a...

    ive always had great luck with shoe goo. just a little bit of that stuff goes a long way. and if you want to remove it warm it up with a heat gun and it rolls right off. i have never had it unstick...
  16. Replies
    9
    Views
    377

    i dont think i could stand them rusted screws.

    i dont think i could stand them rusted screws.
  17. Replies
    9
    Views
    288

    yeah that is true, but after this ill deffentally...

    yeah that is true, but after this ill deffentally stick to venom for all my brushed motor needs
  18. Replies
    14
    Views
    882

    sellinchevs seeing the slashes built like that...

    sellinchevs seeing the slashes built like that gave me the inital idea, but i never really had a slash chassis so i have been useing a scratch built "slash" chassis.

    finding the time isnt the...
  19. Replies
    9
    Views
    288

    i havent had a venom batter splode on me yet. and...

    i havent had a venom batter splode on me yet. and ive had a 1800 for about 3 years and its been to **** and back...
  20. Replies
    14
    Views
    882

    it was purpose built. straight line speed...

    it was purpose built. straight line speed machine. like i sayed the tieraps will be replaced with fuel line inside the shocks. after i sold my 4-tec i have wanted another on-road, and the slash gave...
  21. Replies
    3
    Views
    208

    ist where the 2 halves of the case go toghether....

    ist where the 2 halves of the case go toghether. it shows up after you pull it apart a few times.
  22. Replies
    9
    Views
    288

    only the nickle metals, the lipos are great

    only the nickle metals, the lipos are great
  23. Replies
    14
    Views
    882

    ok, sorry for the delay, but i finally got pic...

    ok, sorry for the delay, but i finally got pic
    http://i158.photobucket.com/albums/t117/gasshead/rc%20cars/DSCI0727.jpg
    http://i158.photobucket.com/albums/t117/gasshead/rc%20cars/DSCI0729.jpg...
  24. Replies
    9
    Views
    288

    venom CS awesome

    i bought a 15t double motor from venom racing, ran it 5 minutes and it puked out on me. e-mailed them all they asked for was a picture. i now have a NEW 15t motor on its way free of charge.

    i know...
  25. Replies
    14
    Views
    882

    lowest slash??

    hey guys, been tinkering on a SS slash..."super street". i beleive i have the record for the elowest center chassis clearance for a slash. its around a half an inch, ill get a picture of it tommrow...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4