Search:

Type: Posts; User: morganko

Page 1 of 20 1 2 3 4

Search: Search took 0.16 seconds.

  1. Replies
    13
    Views
    1,722

    you should look in the Market Place on these here...

    you should look in the Market Place on these here forums...wink, wink!! POINTS!!! =)
  2. Replies
    12
    Views
    404

    I used the stock plastic towers and cut them to...

    I used the stock plastic towers and cut them to fit to give me some strength and height....

    http://lh6.ggpht.com/-YeXfhOxnWbU/TjR-PLc9MlI/AAAAAAAAAsI/Uo-z0UGNzDQ/s640/2011-07-30%25252016.55.16.jpg...
  3. Thread: MPH Challenge

    by morganko
    Replies
    636
    Views
    41,530

    John Force would be proud!

    John Force would be proud!
  4. Thread: MPH Challenge

    by morganko
    Replies
    636
    Views
    41,530

    I have got mine to do over a 100mph a couple...

    I have got mine to do over a 100mph a couple times, on the freeway. But that was while it was in the back of the pickup =)
  5. Replies
    113
    Views
    3,196

    its always good to know Snook and his genius...

    its always good to know Snook and his genius never let up!! =)
  6. Replies
    11
    Views
    755

    Selling my rig...

    I will have it posted tomorrow morning over there but was justgiving a heads up hear incase anyone would be interested. And know, the decision was not made in anger or my lack of rc truck skillls....
  7. Thread: Screw kit

    by morganko
    Replies
    1
    Views
    303

    Tonys Screws

    Tonys Screws
  8. Replies
    23
    Views
    943

    fortunately my neighbors get a kick out of...

    fortunately my neighbors get a kick out of watching me run mine around. Especially when I am racing cars going by ;) They all camp on their porches, hootin and hollerin :)
  9. Thread: t-maxx 2.5

    by morganko
    Replies
    8
    Views
    441

    what tphill said

    what tphill said
  10. Thread: t-maxx 2.5

    by morganko
    Replies
    8
    Views
    441

    so it needs to cool off before you can get it...

    so it needs to cool off before you can get it started again??
  11. Replies
    35
    Views
    833

    I would say you could bend anything if hit hard...

    I would say you could bend anything if hit hard enough. I would not run aluminum posts and they way I am always hitting things aluminum a arms would prolly not be a good investment for me.
  12. Replies
    28
    Views
    929

    That I dont know about. I would say it would but...

    That I dont know about. I would say it would but I am not familiar with their warranty. You could try using a piece of aluminum to secure it from the bottom or washers as was suggested.

    I had to...
  13. Replies
    35
    Views
    833

    LOL there is some truth in what he said Snook but...

    LOL there is some truth in what he said Snook but for piece of mind I prefer the aluminum bulks. I did buy a nice set of t-handle hex drivers the other night. Next is some good screws :)
  14. Replies
    28
    Views
    929

    or just drill your own hole where you need it....

    or just drill your own hole where you need it. You wont compromise your chassis.
  15. Replies
    35
    Views
    833

    I wouldnt argue much with what you said.

    I wouldnt argue much with what you said.
  16. Replies
    13
    Views
    1,375

    ohhhh I thought you meant higher up on the...

    ohhhh I thought you meant higher up on the sidewalls. Real beadlocks may help to keep that from happening but I havent tried them so I am not sure.
  17. Replies
    35
    Views
    833

    No loctite but I remember when putting the new...

    No loctite but I remember when putting the new bulks on the screw alignment was a bit difficult so it is probably pinched in the hole. Gonna try taking the other three out to give it some relief and...
  18. Replies
    23
    Views
    943

    get your neighbors a pack of foam ear plugs. :)

    get your neighbors a pack of foam ear plugs. :)
  19. Replies
    35
    Views
    833

    lol no comment

    lol no comment
  20. Replies
    35
    Views
    833

    May just go that route too

    May just go that route too
  21. Replies
    35
    Views
    833

    C4 ? .

    C4 ? .
  22. Replies
    35
    Views
    1,325

    Popeye rocks!! ahhhh-ga-ga-ga-ga-ga-ga-ga ...

    Popeye rocks!! ahhhh-ga-ga-ga-ga-ga-ga-ga
    http://l.yimg.com/us.yimg.com/i/mesg/emoticons7/111.gif
  23. Replies
    35
    Views
    833

    if it would allow me to get it out and not have...

    if it would allow me to get it out and not have to get a new bulkhead, I'd do it but there isnt enough material left now. Gonna try MV's suggestions
  24. Replies
    35
    Views
    833

    cant do the slot anymore after I used the...

    cant do the slot anymore after I used the extraction bit. :(
  25. Replies
    35
    Views
    1,325

    not gonna do it....nope, not gonna.

    not gonna do it....nope, not gonna.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4