Search:

Type: Posts; User: InceptorOne

Page 1 of 2 1 2

Search: Search took 0.17 seconds.

  1. Replies
    6
    Views
    76

    True, realized I just need extenders for 12mm......

    True, realized I just need extenders for 12mm... Ya maybe the 2wd ones will help.
  2. Replies
    6
    Views
    76

    Wider offset for F11 wheels

    I think I mistakenly bought the wrong F11 wheel. I already mounted them but the wheelbase becomes a lot more narrow than expected... can I just use a hex adpater to widen it?

    I got:...
  3. body reamer does the trick for me, easier to be...

    body reamer does the trick for me, easier to be more precise and mark how deep to go.
  4. whats good practice for new flotek body?

    simple question, mostly a matter of opinion... does it matter if I cut the airflow holes before or after painting? i still have the overspray film on, but i did a couple holes already to test how...
  5. Replies
    13
    Views
    226

    one of mine broke recently too, I just took a...

    one of mine broke recently too, I just took a small piece of gorilla tape and wrapped around the crack, still holding up! plus its the only stock traxxas plastic part to actually crack or break on...
  6. Replies
    8
    Views
    175

    I might try the 18T which i have on hand... Temps...

    I might try the 18T which i have on hand... Temps are usually fine all around and i rarely hit the full throttle if ever on a single lap at my track.
  7. Replies
    8
    Views
    175

    With heavy use and a few runs going through 2-3...

    With heavy use and a few runs going through 2-3 lipo packs, the motor only gets up to about 120.
  8. Replies
    8
    Views
    175

    Should i up my pinion? (Mmp system)

    Im running a 13t pinion with a castle 3800kv motor through a mmp system on 2s lipo... I have no issues with temps at all, im wondering how much higher can i go? Past the 15T max recommended by castle?
  9. Replies
    4
    Views
    110

    hinge pins slipping

    the short hinge pins on the suspension arms, mine keeps slipping a bit on one wheel... it doesn't actually fall out fully, the threaded portion just gets exposed. any ideas to remedy?
  10. Thanks guys. Considering the fallbacks of the...

    Thanks guys. Considering the fallbacks of the metal one i'll probably get the hybrid rubber/metal ones avid offers.
  11. Is there a full bearing replacement set?

    I burned out two of the bearings in the right rear wheel assembly so I figure the rest need to be changed and upgraded. Is there a full replacement set, preferably an upgrade so I can swap out all...
  12. Replies
    8
    Views
    136

    hmm i'll have to remember where i put those now...

    hmm i'll have to remember where i put those now lol, thanks!
  13. Replies
    8
    Views
    136

    what do you do for a screw collar/shoulder?

    what do you do for a screw collar/shoulder?
  14. Replies
    21
    Views
    355

    i have two Sky Lipos and two Gens Ace lipos off...

    i have two Sky Lipos and two Gens Ace lipos off HobbyPartz, both brands are 2s 5000mah 40C and have had no issues with them at all.
  15. Replies
    8
    Views
    136

    I thought threadlock only works well for metal on...

    I thought threadlock only works well for metal on metal?
  16. Replies
    8
    Views
    136

    Shock cap screws keep slipping out

    I have the big bores with the stock shock tower and two of my left shocks slipped out at the top caps yesterday, just race/bashing at the track. I have extras I popped in but I know the holes are...
  17. Replies
    740
    Views
    378,112

    Sticky: Ready for 2014 after a long hiatus! Standard...

    Ready for 2014 after a long hiatus! Standard Kuhmo wheels for looks and testing for now.

    http://i.imgur.com/5ZsgAFF.jpg
    http://i.imgur.com/WWX78MH.jpg
  18. Just an update, I put some shock oil on them and...

    Just an update, I put some shock oil on them and it worked wonders! very smooth and loose now... there is just one end that was damaged by grit and would not cooperate, even after taking the ball...
  19. What kind of oil works best?

    What kind of oil works best?
  20. Rod ends/pivot balls binding and friction issues

    Trying to get my slash 4x4 ready for the season but noticed a lot of unessesary sticking and friction when I take my shocks off all four wheel assemblies. It acts a lot more looser when I take the...
  21. Replies
    740
    Views
    378,112

    Sticky: My upgraded slash with brand new body off an ebay...

    My upgraded slash with brand new body off an ebay auction for $80. inside is a MMP with a 2400kv motor and a 2s 5000mah 40C Sky Lipo.

    http://i45.tinypic.com/2zsybn6.jpg...
  22. Replies
    14
    Views
    609

    They shipping you one for free or do you have to...

    They shipping you one for free or do you have to send yours in with the $50 form to fill out?
  23. Replies
    14
    Views
    609

    Same exact thing happened to me recently buddy!...

    Same exact thing happened to me recently buddy! Only ran it for about 10 minutes on a beach, full throttle tho. Gonna upgrade to a mamba max pro with 3800kv motor, among some other minor upgrades....
  24. Replies
    7
    Views
    414

    8.4v for 7.4v 2s? sry if thats a noob question...

    8.4v for 7.4v 2s? sry if thats a noob question lol.
  25. Replies
    7
    Views
    414

    i volt tested the plug, it was 7.65 for all of...

    i volt tested the plug, it was 7.65 for all of them. i'm not sure what each cell might be, how do i figure it out?

    Update: Tested the voltmeter to the balancing cable and got a reading of 3.82? is...
Results 1 to 25 of 47
Page 1 of 2 1 2