Search:

Type: Posts; User: C6 Z06

Page 1 of 20 1 2 3 4

Search: Search took 0.39 seconds.

  1. Replies
    11
    Views
    342

    Tighten the clutch bell? You mean slipper-clutch?

    Tighten the clutch bell? You mean slipper-clutch?
  2. Replies
    18
    Views
    338

    Just use a good quality, well-known...

    Just use a good quality, well-known fuel...COUGH*O'DONNELL'S-30%-RACEBLEND*COUGH
  3. Replies
    17
    Views
    356

    I like Acer's bearings and, so far, Avid's...

    I like Acer's bearings and, so far, Avid's bearings...and Traxxas blue-rubber bearings seem to be decent, too.
  4. Replies
    8
    Views
    262

    Sweet! I currently use a full set (28pcs) of...

    Sweet! I currently use a full set (28pcs) of Craftsmen HD (red rotating cap) hex drivers, nut drivers, pliers, cutters, & T-Handles...can't wait to get my TiNi drivers!
  5. Oh yea, I am no longer looking for new stuff,...

    Oh yea, I am no longer looking for new stuff, except the small stuff like knucklehead towers etc, used is just fine as long as it is still in good condition.

    You still gonna try to buy that NIP...
  6. Replies
    17
    Views
    356

    It is a Traxxas question, the Axial is in...

    It is a Traxxas question, the Axial is in Traxxas-Born vehicle...hehe!

    I have actually used liquid nitrogen to cool a 1:1 pinion and an oven to heat a 1:1 bearing-race...nothing else we tried...
  7. Replies
    8
    Views
    262

    I actually just ordered a new 7pc Integy TiNi...

    I actually just ordered a new 7pc Integy TiNi hex-driver set last night! :)
  8. Yea, I really did think I was never going to dive...

    Yea, I really did think I was never going to dive into the UE pool, and if I did, I would only buy brand-new parts...but then I got some new Knucklehead towers, and that's all it took! Now I am...
  9. Replies
    17
    Views
    356

    I think those will do just fine...let us know how...

    I think those will do just fine...let us know how the install goes. Do you use the freeze and heat method?
  10. Replies
    45
    Views
    951

    How about we learn not to flame others....

    How about we learn not to flame others....
  11. Thread: Free hop-ups!

    by C6 Z06
    Replies
    9
    Views
    515

    -› Written by Chad S. Roe (C6 Z06...

    -› Written by Chad S. Roe (C6 Z06)

    BRAKES:
    Yea, I run the ball-point pen "spring mod"...the springs hold the brake calipers away from the brake rotor so that they don't drag, which can slow you...
  12. Thread: do

    by C6 Z06
    Replies
    4
    Views
    248

    Ummm...give Traxxas a call, I am sure they can...

    Ummm...give Traxxas a call, I am sure they can lead you down the right road to the manufacturer who produces that screen material for them...unless it's made at Area51, SkunkWorks, or BlackOps...
    ...
  13. Replies
    17
    Views
    535

    Just put a Phillips head screw driver in the end...

    Just put a Phillips head screw driver in the end of the header and wallow it around, fluting the end of the header to the desired size...works like a charm!
  14. Replies
    22
    Views
    546

    I vote 3.3...

    I vote 3.3...
  15. What happens when you hit the button? Do any...

    What happens when you hit the button? Do any lights come on? Does the engine try to turn over? Does the engine turn over, but just won't start?
  16. Well, I have a UE GenIV SS now, so no more SS...

    Well, I have a UE GenIV SS now, so no more SS problems! ;)
  17. Thread: motor swap

    by C6 Z06
    Replies
    13
    Views
    269

    Yes sir!!! :) ;)

    Yes sir!!! :) ;)
  18. Replies
    9
    Views
    512

    Nice! Guess I will be doing this soon, whenever I...

    Nice! Guess I will be doing this soon, whenever I buy your VBS! :)
  19. Replies
    12
    Views
    420

    Man, I am so anxious to see what that LRP Z.28R...

    Man, I am so anxious to see what that LRP Z.28R Spec-3 3.95HP does to the Traxxas CVD axles!!! <devilish grin>

    My money is on the fact that they will snap where the dowel-pin goes through the...
  20. What do you want for them?

    What do you want for them?
  21. Yea, I really want to add VBS & Racer-X to the...

    Yea, I really want to add VBS & Racer-X to the SM, and I also want to find a nice Predator chassis (not nickel plated), but I know when I get it, I will immediately want VBS & Racer-X on it, too!...
  22. Replies
    17
    Views
    356

    I can't find the other bearing on Avid's site,...

    I can't find the other bearing on Avid's site, but you may not even need it if you are just replacing the front beaing.

    They are expensive, but I would go with "Edit 2", because they are a mix of...
  23. Replies
    17
    Views
    356

    Hmmm...I, personally, would go with the bearing...

    Hmmm...I, personally, would go with the bearing that has the best specs, you know? But, I am not sure if it is ok to run a fully sealed bearing in the front of the engine. My logistical brain says to...
  24. Cool, thanks...just bought a NIP pair for $17!...

    Cool, thanks...just bought a NIP pair for $17! And they're red, so they'll match my truck! :)

    Man, I feel a huge buying spree coming on...hope my plastic doesn't melt from all the use! ;)
  25. Need to verify correct length "Traxxas Tubes" to get...

    Ok, I have a 2.5 T-Maxx with 3.3 knuckles/carriers and axle-shafts, will the Traxxas Tubes for the front of the 3.3 T-Maxx fit the front of mine? They are part #5141R and are 112mm long. I am...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4