Search:

Type: Posts; User: bulkhead

Page 1 of 4 1 2 3 4

Search: Search took 0.17 seconds.

  1. Replies
    9
    Views
    215

    cheers,thanks.

    cheers,thanks.
  2. Replies
    9
    Views
    215

    my 2 speed messed up,thought I'd give it a try,I...

    my 2 speed messed up,thought I'd give it a try,I race it on the weekends,don't really need the 2-speed on that track,but I'll eventually go back..
  3. Replies
    15
    Views
    252

    I tried everything,I even put a new piston and...

    I tried everything,I even put a new piston and sleeve,new carb,sealed everything,it still did the same thing...and it was the silver head engine.I couldn't figure it out..
  4. Replies
    9
    Views
    215

    right now I have a 22t clutch bell,with 72...

    right now I have a 22t clutch bell,with 72 spur,its o.k,but I need to find the right gearing,right now its lacking a bit low end,it be nice to now what the single speed trucks where running,so I...
  5. Replies
    9
    Views
    215

    pro 15 question?

    the pro 15 was single speed,right?,the reason I'm asking is,I recently converted my t-maxx to a single speed,just to give it a try,I was wondering if anyone now's what the stock pro 15 gearing was?
  6. Thread: Motor help

    by bulkhead
    Replies
    4
    Views
    158

    I think with smaller tires,and the right...

    I think with smaller tires,and the right gearing,it should do wheelies,mine used to,when it ran..
  7. Replies
    15
    Views
    252

    lots of people have that problem,I couldn't...

    lots of people have that problem,I couldn't figure it out also,I found that those motors are very hard to keep running,compaired to my other motors,I ended up almost giving it away...but for the...
  8. Replies
    12
    Views
    252

    look at the gears....there's a pin that holds it...

    look at the gears....there's a pin that holds it on to the shaft...if the pin breaks,or comes loose,the gear will just spin on the shaft,and your truck won't move,check that..
  9. Replies
    0
    Views
    135

    help with single speed..

    I just put a single speed conversion in my t-maxx,wondering what sort of gearing I should run?,I have 24t clutch bell,70t spur at the moment,not really liking it..it revs very high when I let off the...
  10. Replies
    12
    Views
    252

    check if any off the pins are broken...

    check if any off the pins are broken...
  11. Thread: single speed

    by bulkhead
    Replies
    4
    Views
    195

    there must be somebody with a single speed?

    there must be somebody with a single speed?
  12. Thread: single speed

    by bulkhead
    Replies
    4
    Views
    195

    single speed

    just ordered a single speed for my maxx,I have an hpi s-25 in it at the moment,I raced a little at the track,and it seems like a 2 speed isn't needed,just wondering for those who have it,do you like...
  13. Replies
    1,143
    Views
    611,786

    Sticky: nice truck campracing,here's some old pic's of...

    nice truck campracing,here's some old pic's of mine..
    http://i3.photobucket.com/albums/y58/flyhi/Picture067.jpg
    http://i3.photobucket.com/albums/y58/flyhi/Picture066.jpg...
  14. Replies
    13
    Views
    357

    my spur used to rub the air filter,couldn't...

    my spur used to rub the air filter,couldn't figure it out for a long time,I later found out that the chassy was bent,after I replaced it,it was fine..
  15. Replies
    17
    Views
    362

    I had that problem before(when I first...

    I had that problem before(when I first started)idle was way high,I later found out,like a couple people said above,the lsn was lean,I'd bet money its that..
  16. Replies
    5
    Views
    210

    well,if you didn't brake it,you would have...

    well,if you didn't brake it,you would have probably still been there,when I have a good day,I usually kick it up a notch,and if it breaks,its usually worth it!!
  17. Replies
    16
    Views
    415

    I beat my intergy bulks,they broke the chassy...

    I beat my intergy bulks,they broke the chassy once,but the bulks are fine,I got my moneys worth..
  18. Replies
    15
    Views
    399

    +1,its just the sound thats a little...

    +1,its just the sound thats a little irratating,not to nock the maxx,but it would have been a little better if it had a little more suspention travel,but I did quite a few mods to it,its good now..
  19. do what they said,or rpm,rpm,rpm,I haven't broken...

    do what they said,or rpm,rpm,rpm,I haven't broken anything thats rpm yet..
  20. Replies
    15
    Views
    399

    I tried a few defferent combos to try to fix that...

    I tried a few defferent combos to try to fix that problem,I finally gave up,lets face it,its a lower riding truck,I don't think anything can be done to make it stop bottoming out,I have a savage,it...
  21. Replies
    8
    Views
    318

    2 sec. is to fast,I set mine to about 3-5,the low...

    2 sec. is to fast,I set mine to about 3-5,the low speed is just for throttle response,you shouldn't have to mess with it much,usually its the high speed needle that causes issues..if its to rich,it...
  22. Replies
    9
    Views
    272

    I wouldn't do that,if you put in a bigger...

    I wouldn't do that,if you put in a bigger screw,it means the chassy hole will have to be bigger,that will weaken it,and it could crack,I'd goop some glue in it for now.....then fix it..
  23. Replies
    3
    Views
    173

    mine used to do that,"might" mean the mesh is a...

    mine used to do that,"might" mean the mesh is a little loose though,I only say that because mine dosn't do that now that I mesh mine a little tight,as for the jerking,its normal,thats just the...
  24. Replies
    10
    Views
    368

    like maxxbash said,its probably a simple linkage...

    like maxxbash said,its probably a simple linkage promblem....
  25. Thread: car vs tmaxx

    by bulkhead
    Replies
    24
    Views
    415

    thats not dirty....this is dirty....that was a...

    thats not dirty....this is dirty....that was a good day!!
    http://i3.photobucket.com/albums/y58/flyhi/Picture001.jpg
Results 1 to 25 of 83
Page 1 of 4 1 2 3 4