Search:

Type: Posts; User: TJK74

Page 1 of 20 1 2 3 4

Search: Search took 0.29 seconds.

  1. Replies
    57
    Views
    3,822

    Definately sounds more like a gear mesh problem....

    Definately sounds more like a gear mesh problem. You should hear the slipper for maybe 3ft.-5ft max depending on how it is set. Anythin g you hear when off the throttle is a bad mesh combination
  2. Replies
    57
    Views
    3,822

    I have used this method over and over and all of...

    I have used this method over and over and all of my cars are brushless and have yet to have a problem or come anywhere close to blowing anything up:wacko:
  3. Replies
    57
    Views
    3,822

    What Battery are you running? any good fully...

    What Battery are you running? any good fully charged 7-cell should be able to pop it right up when holding both tires and with the slipper tightened up.
  4. Replies
    58
    Views
    5,205

    There is no balloning issues with these tire as...

    There is no balloning issues with these tire as with most 1/8 tread cause of their super low profile. I run them on VXLs on all 3 of my cars with no issues.
    VXL Beast & VXL Rocket use these tires...
  5. Replies
    58
    Views
    5,205

    I'll see if I can swap them onto the slash later...

    I'll see if I can swap them onto the slash later and get a pic. Here they are on my kids car. The dish wheels sit about an 1/8" narrower than the spokes but I'm honestly not impressed with the dish...
  6. Thread: promatch?

    by TJK74
    Replies
    2
    Views
    205

    The 4200 are stick packs vs SxS packs. I...

    The 4200 are stick packs vs SxS packs. I personally would get the SXS configuration and the 4600's you get a longer lasting and better performance pack. If your on a budget then go the the 4200's...
  7. Replies
    44
    Views
    796

    you can also use the hex hardware that's used for...

    you can also use the hex hardware that's used for the servo or the front body mount. they have the larger hex and a slight shoulder on them that allows you to get them as tight as they need to be...
  8. Replies
    44
    Views
    796

    I used to do the paper thing. Now I just eye ball...

    I used to do the paper thing. Now I just eye ball it the spin spur by hand and feel for any resistance since most spurs have a slight wobble it is natural for ther to be tigh and loose spots.
  9. Replies
    55
    Views
    1,362

    http://www.nikkoamerica.com/rc/trucks/offroad_truc...

    http://www.nikkoamerica.com/rc/trucks/offroad_truckn/10th.html

    http://www.rchobbyexplosion.com/Nikko_Remote_Control_Trucks_s/15.htm
  10. Replies
    3
    Views
    201

    looks good I ran that set up on both of my...

    looks good
    I ran that set up on both of my bandits for a while and love the way in handled and worked especially in the rough stuff. Longer spindles and run the frons on the rear and the rears on...
  11. Replies
    28
    Views
    460

    Very Wrong Call or ask for Duncan at...

    Very Wrong Call or ask for Duncan at 1-888-TRAXXAS(872-9927)
    Just now called him and His exact words were that the stock shaft are mild steel and the TiNi's are Hardened Steel.

    Click and scroll...
  12. Replies
    5
    Views
    342

    I just cut out a rectange of duct tape and even...

    I just cut out a rectange of duct tape and even run it a bit longer so it goes over the frint edge up to where the case meets the chassis
  13. Thread: shock screws?

    by TJK74
    Replies
    15
    Views
    666

    It happens on most cars especially when running...

    It happens on most cars especially when running alum caps from the friction between the cap and the screw when the suspension cycles it naturally causes it to back out. Use a but of thread lock and a...
  14. Thread: New Track!

    by TJK74
    Replies
    40
    Views
    589

    Get a couple of Losi micro's on that thing and...

    Get a couple of Losi micro's on that thing and you'll have a blast<_<
  15. Replies
    9
    Views
    346

    I run their hardened steel pinions and love them....

    I run their hardened steel pinions and love them. They hold up awesome even when running in grit and sand
  16. Replies
    28
    Views
    460

    I have had them about two months and they are...

    I have had them about two months and they are holding strong. The coating is still in perfect shape and I havent bent one yet. The TiNi are hardened steel and the stockers are chrome mild steel. Lets...
  17. Replies
    28
    Views
    460

    The standard shafts are mild steel and the TiNi...

    The standard shafts are mild steel and the TiNi are hardened steel just like a drill bit.
  18. Replies
    16
    Views
    4,731

    I recently did the conversion on both my bandits...

    I recently did the conversion on both my bandits but used slash arms, links and shafts all the way around. They are easy to find and cheap. Plus since I also run a slash it keeps all the parts the...
  19. Replies
    2
    Views
    125

    I'll throw Pro-Match in the mix for you as well....

    I'll throw Pro-Match in the mix for you as well. Both SPC and Pro-match make excellent quality NiMh pack that with easily out perform your venom packs. I also suggest if you can to go for a matched...
  20. Replies
    28
    Views
    460

    I run the big bore caps on the stock bodies with...

    I run the big bore caps on the stock bodies with TiNi shafts and bump stops and so far they have been bullet proof and leak free.
  21. Lipo's catch fire and burn hot and fast. NiMh...

    Lipo's catch fire and burn hot and fast. NiMh either swell and break open or explode. When they explode they are equal to a mini shotgun shell
  22. I have found the biggest problem with getting a...

    I have found the biggest problem with getting a rustler to track strait is tha fact that the rear arms on the rustler have no toe in. My neighbor was having the same problem till I let him borrow a...
  23. Replies
    8
    Views
    345

    Taller gearing draws more load on the battery...

    Taller gearing draws more load on the battery there for making it produce shorter run times:D
  24. Replies
    58
    Views
    5,205

    Here are some pics compered to a worn Stock tire...

    Here are some pics compered to a worn Stock tire and a brand new Alias.
    http://i237.photobucket.com/albums/ff29/amsoilrep/IMG_0456.jpg
    http://i237.photobucket.com/albums/ff29/amsoilrep/IMG_0457.jpg...
  25. Replies
    58
    Views
    5,205

    Yes they would definately work on that type of...

    Yes they would definately work on that type of track. There are also plenty of other tires that would do the trick as well but they are usually 2-3 times the cost.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4