Search:

Type: Posts; User: Third Coast RC

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    347

    I have the XO-1 adapters and love them on my...

    I have the XO-1 adapters and love them on my slayer, really opens up wheel selection (or pre-glued). The part # is TRA6869.
    Good luck!
    Justin
  2. Replies
    4
    Views
    305

    +1 on the rally build, some good ideas

    +1 on the rally build, some good ideas
  3. Replies
    4
    Views
    295

    They are 55mm with the 32mm shock shafts and they...

    They are 55mm with the 32mm shock shafts and they also make 29mm shafts. You will have plenty if adjustment with them.
    Good luck
    Justin
  4. Slayer Pro won't suck fuel to carburetor.

    I can think of a few things it could be. Sounds like an air leak. Did you take the engine apart (con rod?)
    - You may try to find the air leak, YouTube nitro engine air leak there r good videos on...
  5. Replies
    3
    Views
    250

    I use 50wt in all my revo shocks, which are GTR's.

    I use 50wt in all my revo shocks, which are GTR's.
  6. Replies
    1
    Views
    333

    I don't think the diffs will hold diff oil. It...

    I don't think the diffs will hold diff oil. It looks like there is some bearing grease or something similar (I use moly grease). I have heard of ppl using silly putty to "lock" the diffs, but have...
  7. Replies
    21
    Views
    488

    Question for all

    Carter,
    I rebuild my trans 2x per year, look at the gears, replace any that appear worn and check/ replace any bearings that need it.
    I understand the if it ain't broke don't fix it motto, but I...
  8. Replies
    6
    Views
    298

    I've had a few air leaks not associated with air...

    I've had a few air leaks not associated with air filters or carbs and it is typically the front bearing seal and you'll notice some fluid leaking from behind the clutch bell
    I guess some ppl pre...
  9. Replies
    6
    Views
    298

    erratic performance

    Mitch,
    A small hole in your intake tube can cause erratic performance, and can seriously shorten your engine life. I tend to go through tubes pretty often, our track has some large jumps and a crash...
  10. Thread: shocks

    by Third Coast RC
    Replies
    6
    Views
    157

    +1 nitronaught I use 50wt in my revo and 40wt in...

    +1 nitronaught
    I use 50wt in my revo and 40wt in my slayer
  11. Thread: shocks

    by Third Coast RC
    Replies
    6
    Views
    157

    I believe it's 30wt, but not 100%.

    I believe it's 30wt, but not 100%.
  12. Replies
    14
    Views
    533

    take a cap off of lexan paint (its the perfect...

    take a cap off of lexan paint (its the perfect size) and drill the top of it enough to fit over the end of the filter (so it can be clipped on). this mod helps to keep water from getting on the...
  13. Replies
    11
    Views
    606

    getting new slayer, any good hopups

    I have the;
    - center diff & rear breaks from integy (Carbon fiber)
    - 12mm hex's for 6mm spindles (larger selection of rims)
    - heavy duty diffs from eRevo
    - badlands on slash offset rims
    - tekno...
  14. Replies
    4
    Views
    254

    Revo is about 17"

    Revo is about 17"
  15. Replies
    4
    Views
    195

    +1 on Double G, I carry lots of extra filters and...

    +1 on Double G, I carry lots of extra filters and change them often. There is an after market pre filter that fits over the stock dual stage filter, but I have not tried it
  16. Replies
    4
    Views
    248

    PTTM, I would start with a good baseline on hte...

    PTTM,
    I would start with a good baseline on hte anti-squat blocks, install the 1.5o and measure ride height then oinstall the 3.75o an remeasure. From there you should be able to determine your best...
  17. Replies
    13
    Views
    272

    If speed is your goal, the Jato is the way to go...

    If speed is your goal, the Jato is the way to go (google BSwift - 93mph), if bashing is more important, the Maxx or Revo may be a better route. Tuning is tuning, all these trucks uset the same 3.3,...
  18. Replies
    13
    Views
    272

    RCKid987, The Jato is a great first nitro,...

    RCKid987,
    The Jato is a great first nitro, Slayer was my first, but a jato followed shortly behind it. If you've driven lots of RC you'll be fine with the jato. Its real quick and can be a bit...
  19. Replies
    4
    Views
    248

    PTTM, I have not tried RPM's on the rear of my...

    PTTM,

    I have not tried RPM's on the rear of my Jato (they r on the front), but the RPM's website says they have kept the same geometry as stock. If you have a toe guage, try measuring the...
  20. Replies
    11
    Views
    302

    Yes, gel then liquid to finish. I use the cheap...

    Yes, gel then liquid to finish. I use the cheap dollar store myself and have not had any problems.

    I remembered another tip:
    Once scuffed and cleaned assembled the wheels and tires and push the...
  21. Replies
    11
    Views
    302

    Glueing tires

    Not sure where I originally read about this process, but here is how I glue my tires;
    1. Clean tires ( especially the bead)
    2. Scuff and clean the rims, I use fine grit sand paper on the beads
    3....
  22. Replies
    3
    Views
    387

    Jato SC wheels

    Hello all,

    I am attempting to put SC wheels and tires on my jato and would like to find front wheels with push in bearings (similar to the stock 2.8s on the front).

    I have tried the rustler...
  23. Replies
    8
    Views
    514

    I have run the badlands on dirt for a couple of...

    I have run the badlands on dirt for a couple of years and I love them. I have not run them on grass, but I think the would get great traction (maybe to good). Btw I run badlands on my revo slayer and...
  24. Replies
    12
    Views
    505

    Thanks for the quick replys, Aft and Hum. I...

    Thanks for the quick replys, Aft and Hum. I bought the tekno's and they wobble. I'm going to try the XO-1's.
  25. Replies
    12
    Views
    505

    Does anyone know if the XO-1 hex's (6869)...

    Does anyone know if the XO-1 hex's (6869) referenced above use the large slayer pins versus the smaller pins the come from tekno? The pins in the tekno kit are the same size as the jato uses
Results 1 to 25 of 110
Page 1 of 5 1 2 3 4