Search:

Type: Posts; User: yellowufo

Page 1 of 5 1 2 3 4

Search: Search took 0.16 seconds.

  1. Thread: rear lights?

    by yellowufo
    Replies
    1
    Views
    350

    Had the same thing happen i pulled the new lights...

    Had the same thing happen i pulled the new lights further in and hot glued them...
  2. Replies
    3
    Views
    435

    And u fixed it how????

    And u fixed it how????
  3. Replies
    6
    Views
    379

    Maybe the hot glue from the lights came loose....

    Maybe the hot glue from the lights came loose....
  4. Thread: lights

    by yellowufo
    Replies
    12
    Views
    747

    Oh my oh my

    Oh my oh my
  5. Thread: lights

    by yellowufo
    Replies
    12
    Views
    747

    A fun build.... two ways to do it i preffer a...

    A fun build.... two ways to do it i preffer a series set up,, less wire. Build and test with a nimh battery for saftey reasons
  6. The oil thickness will decide how much damping an...

    The oil thickness will decide how much damping an how fast the rebound will happen. Your sprngs will return the truck back to the ride height, the piston still has to cycle back through the oil so if...
  7. Replies
    7
    Views
    457

    Having your radio off and the trim set to center....

    Having your radio off and the trim set to center. Take the stering horn off the servo turn on the radio and install the horn as close to center as u can then uise your trim to fine tune it.. if this...
  8. Thread: rpm a arms

    by yellowufo
    Replies
    2
    Views
    225

    Just like people drive .. they never look past...

    Just like people drive .. they never look past the hood of their cars...

    Look down the page a bit for an a arm answer
  9. Thread: sand

    by yellowufo
    Replies
    8
    Views
    737

    Brushed o brushless? Fresh or salt water? I made...

    Brushed o brushless? Fresh or salt water? I made a condom to run mie in the snow worked great keeping snow off and out of the truck u can buy a chassie cover also that would help keep some sand out...
  10. Replies
    13
    Views
    846

    Did you get them out? If not look at the part...

    Did you get them out? If not look at the part explosion in the manual you will se thr part they simply push in andthe arms snap out into the slots
  11. Thread: part #7033x

    by yellowufo
    Replies
    16
    Views
    1,253

    Ps. Count your turns if you remove the pillow...

    Ps. Count your turns if you remove the pillow balls helps to get the camber and toe close that is if u remove them.
  12. Replies
    11
    Views
    564

    What a concept

    What a concept
  13. Thread: part #7033x

    by yellowufo
    Replies
    16
    Views
    1,253

    Yesssssssssssss

    Yesssssssssssss
  14. Replies
    11
    Views
    564

    I wonder when yours was made i got mine iin aug...

    I wonder when yours was made i got mine iin aug 12 and many have had the same problem
    before that such a shame it still happens. Send it in and get a new one u pay shipping. Sucks.
  15. Thread: part #7033x

    by yellowufo
    Replies
    16
    Views
    1,253

    A small flatblade can b used jst push in the tab...

    A small flatblade can b used jst push in the tab and the retainer will pop out do the same on the other side and out it comes
  16. Replies
    9
    Views
    364

    Yep you ship it to them they return shipped mine...

    Yep you ship it to them they return shipped mine for free
  17. Replies
    9
    Views
    364

    Mine was past a month. They sent me a new one I...

    Mine was past a month. They sent me a new one
    I told them i thought it was the normal dealling with the reverse to forward delay till i learned the delay is normal the neutral to forward stop shut...
  18. Replies
    9
    Views
    364

    Thats a common pbobem with the esc they replaced...

    Thats a common pbobem with the esc they replaced mine. My problem now is using an inrunner
    esc with a outrunner motor it does cornfused the esc
  19. Replies
    9
    Views
    364

    I Rset the radio to default then calibraited the...

    I
    Rset the radio to default then calibraited the esc and still teh same will try it all again tomorrow and then switch to a new esc i have, the esc is running a different motor then the 380 its...
  20. Replies
    9
    Views
    364

    full throttle

    Seems at times i have to dubble pull the trigger to get full throttle i reset and re calibraaited but still the same any ideas
  21. Replies
    5
    Views
    310

    Did you loosen the bottom screw that holds the...

    Did you loosen the bottom screw that holds the dowel pin?
  22. Replies
    18
    Views
    2,257

    Did i say that out loud??? Lol a thought that...

    Did i say that out loud??? Lol a thought that wont happen for the general public but thanks anyway.
  23. Replies
    18
    Views
    2,257

    27 bucks for a 5buck parts list wow i need to...

    27 bucks for a 5buck parts list wow i need to start making kits myself
  24. Replies
    24
    Views
    780

    Is this a new in box truck?? If so the manual has...

    Is this a new in box truck?? If so the manual has all the blinking codes in fact it has redundent ways to set your trans it is really one of the best trouble shooting
    guides i have seen. And when...
  25. Replies
    24
    Views
    780

    They had you send the chassis in also that seems...

    They had you send the chassis in also that seems odd with minee i just sent the esc in id call again and try to save some cash on shipping
Results 1 to 25 of 114
Page 1 of 5 1 2 3 4