Search:

Type: Posts; User: Ali

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    33
    Views
    1,501

    How much run time should I get from spc 2500 2s &...

    How much run time should I get from spc 2500 2s & spc 1500 3s.
    The reason I ask is that for both batteries I am getting less than 5 mins of run time.
    I have stock motor with ezrun 60a esc.
    I...
  2. Thread: bearings?

    by Ali
    Replies
    29
    Views
    580

    Hey MTV, Which ones are for the rockers and the...

    Hey MTV,
    Which ones are for the rockers and the steering servo saver.
    Thanks
  3. Thread: Suspension

    by Ali
    Replies
    15
    Views
    578

    I am so glad that I went with 50's...

    I am so glad that I went with 50's recommendations....
    Get hr shock bodies, summit red seal, gpm springs (you can buy three spring sets for around $10), use a blue- black- blue o ring combo to seal...
  4. Thread: snow chains

    by Ali
    Replies
    8
    Views
    703

    Walmart sells chains in small boxes and the one...

    Walmart sells chains in small boxes and the one that I was looking into for some snow chains was for $5-6 for a box of 20 foot chain. Its in their electrical/ hardward isle. you cant miss it or just...
  5. Replies
    11
    Views
    821

    Is there an option of punching a hole in the...

    Is there an option of punching a hole in the motor mount plate....
    The size of the hole can be slightly bigger than the pinion gear so that some part of the pinion sits inside/through the hole.
    I...
  6. Replies
    3
    Views
    589

    Lipo Storage charge and Usage

    Hi ...
    I dont run the merv everyday but keep the lipos fully charged so that I dont need to charge them when I need them.
    Questions:
    1. how long can I keep a fully charged lipo (2s & 3s) before...
  7. 50 is absolutely correct ... I followed his...

    50 is absolutely correct ... I followed his recommendations and am happy with the results.
    Hr shock bodies, rpm springs (1. They are taller than stock springs therefore you don't need to add much...
  8. 50 is absolutely correct ... I followed his...

    50 is absolutely correct ... I followed his recommendations and am happy with the results.
    Hr shock bodies, rpm springs (1. They are taller than stock springs therefore you don't need to add much...
  9. Thread: best erevo esc?

    by Ali
    Replies
    45
    Views
    7,129

    I needed the water resistant properties so I...

    I needed the water resistant properties so I short listed Hpi vapor pro and ezrun 60a waterproof esc. Finally bought the ezrun with the programming card.
    Definitely better than the stock
  10. Thread: SPC 3s?

    by Ali
    Replies
    11
    Views
    353

    How much run time can I get from the spc 3s...

    How much run time can I get from the spc 3s battery.
    Mostly speed runs on the road
    Thanks
  11. Replies
    14
    Views
    637

    I am using 100wt shock oil with hr bodies and gpm...

    I am using 100wt shock oil with hr bodies and gpm black ( front) and silver (rear) ... With red seals
    But I have a heavier car about 2.75 to 3 lbs ....
    Ther is no pre load in the front... And very...
  12. Thread: esc

    by Ali
    Replies
    17
    Views
    508

    I am not a pro like some of the members here ...

    I am not a pro like some of the members here
    but did my share of research.
    I went with ezrun 60A waterproof esc (about $45) with the programming card ... its been a very good experience.
    Easy...
  13. Which spacer did you run .... stock or HR?

    Which spacer did you run .... stock or HR?
  14. Why did you replace the middle spacer with the HR...

    Why did you replace the middle spacer with the HR o ring?
    Is it better to have a spacer or an o ring in the middle ...

    Are there any spec difference between the stock o rings and the HR o rings...
  15. Thread: GPM spring rates

    by Ali
    Replies
    9
    Views
    493

    Hey 50 .... I am going to buy the hr bodies and...

    Hey 50 ....
    I am going to buy the hr bodies and use GPM springs on them.
    Where can I find GPM springs only ...
    You also mentioned to buy red seals ... where can I get those
    Thanks
  16. Replies
    32
    Views
    1,263

    What is the spring rating for GPM springs (Black,...

    What is the spring rating for GPM springs (Black, Silver & Gold)
    What does the number represent? Is it ... the amount of weight required to compress the spring by 1 inch or something else.
    ...
  17. Replies
    16
    Views
    1,280

    On the ez60 with 2s the motor and esc hardly get...

    On the ez60 with 2s the motor and esc hardly get warm (no where near HOT) ... So even if I take the fan off with 2s I should be fine.
    It only with the 3s that I am concerned about.

    BTW the fan...
  18. Replies
    16
    Views
    1,280

    Thanks 50, In case it fries up. What are my...

    Thanks 50,
    In case it fries up.
    What are my options ... the current one is 25mm x 25mm x 10mm and this would fit on the ESC fins. Anything bigger might not fit.
    That is why I look up the one in...
  19. Replies
    16
    Views
    1,280

    So I guess I will plug in the 3s and will find...

    So I guess I will plug in the 3s and will find out if it survives or not
  20. Replies
    16
    Views
    1,280

    Jimmie ... The wire on the fan is very small...

    Jimmie ...
    The wire on the fan is very small ... the fan sits on top of the ESC and can only connect to the ESC
    Here is what I have ... its the waterproof version...
  21. Replies
    16
    Views
    1,280

    ESC cooling fan for 2s and 3s Lipo

    I have a ezrun 60a esc which comes with a 7v fan.
    The instructions say not to use it with 3s Lipo (for obvious reasons).
    I really dont need a fan for 2s but was looking into a 12v fan which would...
  22. Replies
    32
    Views
    1,263

    Ok Great. If I go with hr bodies, pls. let me...

    Ok Great.

    If I go with hr bodies, pls. let me know the parts I need to order.
    1. red summit pistons (part number). How is this better than the stock piston?
    2. tin shafts (part number). How is...
  23. Thread: Wing question

    by Ali
    Replies
    19
    Views
    666

    Thanks 50 I read an earlier post, I think it was...

    Thanks 50
    I read an earlier post, I think it was from you where you had talked about boiling the wings to make them more flexible. Did you boil the ofna?
  24. Thread: Wing question

    by Ali
    Replies
    19
    Views
    666

    I was looking at ofna 1/12 scale wing. Has...

    I was looking at ofna 1/12 scale wing.
    Has anyone tried it? Is it a good fit?
    Any other options I might have?
    I have replaced two stock ones and want to try something different
    thanks
  25. Replies
    32
    Views
    1,263

    Hey Cipher ... why the different combo ... gpm...

    Hey Cipher ... why the different combo ... gpm shocks and springs in front and stock shocks and silver gpm springs in the back.

    I know that gpm shocks come with 3 sets of spring. Which one is...
Results 1 to 25 of 68
Page 1 of 3 1 2 3