Search:

Type: Posts; User: hallzazz

Search: Search took 0.04 seconds.

  1. Thread: Hard to start

    by hallzazz
    Replies
    4
    Views
    289

    the temp has never been over 270 and it may be a...

    the temp has never been over 270 and it may be a lil lean but I am blowing out good smoke. I am about to check it out and see if i cant find an air leak...
  2. Thread: Hard to start

    by hallzazz
    Replies
    4
    Views
    289

    323, the piston is charred a bit too

    323, the piston is charred a bit too
  3. Thread: Hard to start

    by hallzazz
    Replies
    4
    Views
    289

    Hard to start

    I have been trying to get a proper tune for my revo in this heat, I ran it for just a few minutes and it died on me... I cant figure out what is causing this! It wont start back up, plug is still...
  4. Replies
    3
    Views
    1,125

    Okay thanks ryan, I dont know how old the venom...

    Okay thanks ryan, I dont know how old the venom battery was when I got it but it would only last for just a few starts and I was constantly having to recharge it! I replaced the piston and sleeve and...
  5. Replies
    3
    Views
    1,125

    EZ start battery ?

    I am looking to purchase a new battery for my ez start because I have been out of the sport for about a year and my 1800 nicd will not charge. Since it is just for a quick start does it really matter...
  6. Replies
    14
    Views
    2,313

    No I sure don't however I put a spring off the...

    No I sure don't however I put a spring off the throttle arm to pull it back into place in case this were to happen again! Not positive that it will work but I figured it probably would do the trick...
  7. Replies
    14
    Views
    2,313

    Sorry but what do you mean by binding?

    Sorry but what do you mean by binding?
  8. Replies
    14
    Views
    2,313

    Ok I got the motor back together, and bought a...

    Ok I got the motor back together, and bought a spur gear today. She started and idled fine, at 160 degrees I took it for a test run to start breaking it in. All was well for about two min of run...
  9. Replies
    14
    Views
    2,313

    That is what I was trying to do, but with the...

    That is what I was trying to do, but with the engine reving up so high I didn't wanna drive it risking it just taking off on me with the way the motor is actin. That is why I burnt a whole tank of...
  10. Replies
    14
    Views
    2,313

    No I still havent drove the truck I just let the...

    No I still havent drove the truck I just let the motor idle.. There was no sign of oil on the outside anywhere, but is it okay for oil to be on top of the piston??
  11. Replies
    14
    Views
    2,313

    The piston was installed correctly but there is...

    The piston was installed correctly but there is oil all over the place! On top of the piston, crankshaft, carb, exaust, everywhere!!! Like I said I am completely new to this and I do not understand...
  12. Replies
    14
    Views
    2,313

    Not positive on the piston cutout, I didnt really...

    Not positive on the piston cutout, I didnt really pay attention to that but I am about to go check and see. If I did do that would the piston and sleeve still be good for use after re-installing in...
  13. Replies
    14
    Views
    2,313

    RPM jump on break in

    First of all i am new to the game, I just bought my first nitro, Revo 3.3 used! I test drove it for two tanks and all was well exept the one way bearing going out. Upon purchase I went to my lhs to...
Results 1 to 13 of 13