Search:

Type: Posts; User: SYN'Z-E-revo

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    5
    Views
    936

    No I'm sorry forget what I said. You can't use an...

    No I'm sorry forget what I said. You can't use an 11.1 due to the bec. Battery eliminator circuit. It would overload the esc. Sorry. I was thinking of a different esc.
  2. Replies
    5
    Views
    936

    Ya you can use one lipo. Plug it into the bed...

    Ya you can use one lipo. Plug it into the bed side. Usually a red tag on the wires. Then make a connector that ties the other conection together. You understand? It will run that way. I've done it...
  3. Replies
    2
    Views
    490

    Yes I did do a search but some people said not to...

    Yes I did do a search but some people said not to break in with water on the titans. Some say do it for 3 mins.
  4. Replies
    2
    Views
    490

    Breaking in brushed motors.

    Ok so I just made the jump to buy me an erevo. It'll be here monday. I bought the brushed version because when I upgrade to brushless, the esc and motors can go on my emaxx. Anyways. I've broke in...
  5. Replies
    10
    Views
    283

    Nothing is stripped. I just tore everything down....

    Nothing is stripped. I just tore everything down. Head, carb, everything. Cleaned it all, etc. just now got it reassembled. I'll try running it today. I got everything set back to factory.
  6. Replies
    10
    Views
    283

    No. I'm gonna spray everything out to where it's...

    No. I'm gonna spray everything out to where it's dry. Take carb off. Reset to factory settings. And start over. Then see where it's at.
  7. Replies
    10
    Views
    283

    Well I had one in it today and it finally killed...

    Well I had one in it today and it finally killed it. So it has a brand new one in it. And I got it running good with it. But still have the rich low end.
  8. Replies
    10
    Views
    283

    I dont think you read it right. I have turned the...

    I dont think you read it right. I have turned the LSN. All the way in up to 4 out. It changes a little but still too much fuel.
  9. Replies
    10
    Views
    283

    Revo 3.3 tuning issues

    Ok so I got this 3.3 used. It runs pretty good on highspeed. It idles ok once ran a little bit I have tried turning the LSN all kinds of ways. It's running rich on the bottom end. And I can't get it...
  10. Replies
    1
    Views
    160

    Revo 3.3 conversion to electric.

    My buddy has a spare 3.3 truck. He's basically gonna give it to me to build. Now I heard something about using emaxx parts. I have a 3906 emaxx, can the trans and motor plate be used from it? Or do I...
  11. What's the best deal shipped? And would you be...

    What's the best deal shipped? And would you be able to do PayPal?
  12. Replies
    684
    Views
    205,505

    If you run axial oversize wheels and big joe...

    If you run axial oversize wheels and big joe 40series tires. How does it drive? What gearing works well with them?
  13. Replies
    5
    Views
    822

    Brushed or brushless?

    Ok so I'm looking at a erevo.i have a 1/16 Vxl and love it's speed but it's so small. Now which would be better to do? The brushed revo is a lot cheaper and it can always go to brushless. How good is...
  14. Replies
    7
    Views
    201

    Ok. What's the two factory ones?

    Ok. What's the two factory ones?
  15. Replies
    7
    Views
    201

    I'm not looking for speed runs just bashing and...

    I'm not looking for speed runs just bashing and driving fast on pavement them slowing down to jump a curb. I know with the factory bigger gear the thing is really fast. But the motor gets hot. I'll...
  16. Replies
    7
    Views
    201

    Best gearing

    I have a stock merv. I'm running a 7.4 lipo. 2200 mah 35c 50c burst. What's the best pinion gear size for speed? I running the speed gearing because it keeps the motor a little cooler. What would be...
  17. Replies
    8
    Views
    522

    I know eventually they will break. I just wanna...

    I know eventually they will break. I just wanna go back to 1/10. I have my emaxx and my 1/16 revo but my friend has the 3.3 revo. And I need a bigger vehicle to keep up now off road.
  18. Replies
    8
    Views
    522

    It's not new so I'm unsure if it's upgraded....

    It's not new so I'm unsure if it's upgraded. Either way. It would be cheaper to convert this to a brushless system than to buy a new one.
  19. Replies
    8
    Views
    522

    Doesn't the brushed revo work with emaxx wheels?...

    Doesn't the brushed revo work with emaxx wheels? I have like 5 sets of good emaxx wheels, and I'd be great if the fit.
  20. Replies
    8
    Views
    522

    Difference to brushless.

    I've found a great deal on a rtr brushed erevo. I already have a 3906 emaxx and a 1/16 revo brushless. I've heard a few parts are better stock on the brushless 1/10 revos. If so what are they? I'm...
  21. Replies
    8
    Views
    407

    That was my plans. Rulex with goosebumps. Anyone...

    That was my plans. Rulex with goosebumps. Anyone with the body. Does it come with the graphics to say raptor before the rear quarters?
  22. Replies
    8
    Views
    407

    I plan on jconcepts wheels anyway. But I'm a...

    I plan on jconcepts wheels anyway. But I'm a Chevy fan too. But unless it's a 88 to 98 style I wouldn't buy it. I'll probably get the body and try it out.
  23. Replies
    8
    Views
    407

    Raptor body?

    How good is the raptor body? I've heard bad about the fitment. Can someone explain who has one?
  24. Replies
    6
    Views
    216

    Yes it's brushless. Less than a year old. Have...

    Yes it's brushless. Less than a year old. Have original box. The body is scratched up. But I'm getting a new body. Chassis and turn bulkes are dyed black. Has all original tools and stuff. Even...
  25. Replies
    6
    Views
    216

    Whats a used merv worth?

    Im thinking I might sell mine because I want a bigger one. Im not sure if this is the right place to ask. It's pretty much stock. Except the springs and shock oil. And the connectors are deans. 27mhz...
Results 1 to 25 of 36
Page 1 of 2 1 2