Search:

Type: Posts; User: Lynnwoodwind

Search: Search took 0.04 seconds.

  1. Replies
    18
    Views
    1,579

    A Baja body works great, I used the Rally rear...

    A Baja body works great, I used the Rally rear bumper and a RPM SC10 front bumper.
  2. Replies
    826
    Views
    482,643

    Sticky: Here's my Bug: Extreme CF chassis Full Pro Trac...

    Here's my Bug:
    Extreme CF chassis
    Full Pro Trac
    MMP with SCT motor
    Spectrum
    Hitec 645mg
    http://i843.photobucket.com/albums/zz351/lynnwoodwind/8-28-10070.jpg
  3. Replies
    15
    Views
    604

    http://http://s843.photobucket.com/upload/albums/l...

    http://http://s843.photobucket.com/upload/albums/lynnwoodwind/
    http://s843.photobucket.com/albums/zz351/lynnwoodwind/?action=view&current=6-2010328.jpg
    I made a plate from aluminum and used servo...
  4. Replies
    10
    Views
    568

    The STRC and Extreme handle the same, STRC is...

    The STRC and Extreme handle the same, STRC is lighter, Extreme feels smoother due to weight. STRC is less to maintain, less attach points, and has less stress points.
  5. Replies
    35
    Views
    3,312

    opps, my first photo and it's TOO BIG, oh well,...

    opps, my first photo and it's TOO BIG, oh well, more practice.
  6. Replies
    35
    Views
    3,312

    Here's a plate that I used along with a proline...

    Here's a plate that I used along with a proline splice plate.
    ...
  7. Replies
    35
    Views
    3,312

    I've been running the same set up all summer,...

    I've been running the same set up all summer, IT'S GREAT, I'd suggest putting in a proline splice plate, those attach points for the motor do break. I'll post some pic's that has been bullet proof.
  8. Replies
    7
    Views
    305

    It may do well in raceing at the track, forget...

    It may do well in raceing at the track, forget about it in bashing. It can't hold up to brushless.
  9. Get an aluminum gear case, Integy T8098 fits the...

    Get an aluminum gear case, Integy T8098 fits the best, and you will not have to worry about heat. I can run my MMP 4600, 19/86, 2 cell, 30-37 min straight and the temp does not go above 145.
  10. Replies
    6
    Views
    2,247

    A Pro-trac set up will take care of the high grip...

    A Pro-trac set up will take care of the high grip corners.
  11. Replies
    20
    Views
    1,476

    I finished up mine and I like it as well if not...

    I finished up mine and I like it as well if not better than my Extreme set up. I was able to attach the MMP to the upper plate and the balance is perfect. With the Proline suspension, you need to...
  12. Replies
    12
    Views
    518

    I've used both the Slice and the Extreme lcg, the...

    I've used both the Slice and the Extreme lcg, the Slice didn't take much time at the track to break the fwd bulkhead, the motor attach point blew out right away. I used some aluminum plates to beef...
  13. Replies
    27
    Views
    3,880

    I've run the MMP 5700 and 4600 in the same...

    I've run the MMP 5700 and 4600 in the same set-up. The 5700 doesn't have the torque getting into and out of corners and setting up for jumps. The 5700 get's hotter 160/170 in about half the time it...
  14. The Rusty RPM arms have no toe-in, the slash...

    The Rusty RPM arms have no toe-in, the slash proline protrac have the toe-in.
  15. Another cheap way is to use the rear arms from...

    Another cheap way is to use the rear arms from the Proline Protrac, $10.00.
  16. Replies
    32
    Views
    1,051

    I tried a fubuta p190 "rate" gyro on the wif'e's...

    I tried a fubuta p190 "rate" gyro on the wif'e's rusty, it was about 39.00 at the lhs, mounted with double back tape in line with the servo. It sure made it easier for her to keep it on the track. I...
  17. I'm using the Integy "T 7987" drive shafts with...

    I'm using the Integy "T 7987" drive shafts with the Protrac/Rustler rear a-arms, mainly bashing at the track. I haven't had any issues. I blow out the cv's and use a syringe of 3-in-1 oil to put a...
  18. Replies
    34
    Views
    1,091

    I've used a #4 split brass washer and spot faced...

    I've used a #4 split brass washer and spot faced the input shaft collars on the diff. It will pretty much completely lock the rear end and still allow the plate to get screwed on fully.
  19. Replies
    0
    Views
    294

    Slice Build

    I'm getting parts around to put a Slice together, tried the itnegy and stock rear end, the fwd attach holes are off, more than I want to slot..Does the Golden Horizon rear end have better fit?
  20. Replies
    16
    Views
    723

    +1 for the Proline, and go with 1/8 calibers in...

    +1 for the Proline, and go with 1/8 calibers in front and 1/8 bowties in the rear. They add height and stability.
  21. Replies
    9
    Views
    571

    I've used it on my stock chassis, and used one in...

    I've used it on my stock chassis, and used one in the repair of an Extreme chassis. I wish I had used it in the Extreme sooner.
  22. Replies
    560
    Views
    164,899

    Nice paint Dr., I would like to post some of my...

    Nice paint Dr., I would like to post some of my shots, and can't figure it out, any ideas. The post rules says no attachements, is that my hang up?
  23. Replies
    12
    Views
    502

    I've had the 4600 and 5700 and agree with the...

    I've had the 4600 and 5700 and agree with the gearing's. Now I'm running a Orion Pro Experience 2 3750, gearing from 18-23/86 2s, temps haven't gone over 105 yet, that's running straight for 40 min.
  24. I've done the mmp 4600 and mmp 5700, go with the...

    I've done the mmp 4600 and mmp 5700, go with the ORION Pro Experience 2 3750. NO heat issues, 86/20, 2s 5000 40c Check Points back to back all day, never been over 96 deg yet.
Results 1 to 24 of 24