Search:

Type: Posts; User: Koreyh

Search: Search took 0.10 seconds.

  1. Replies
    11
    Views
    400

    hmm ill check the connectors on the esc

    hmm ill check the connectors on the esc
  2. Replies
    11
    Views
    400

    Yea where the positive and negative to to the...

    Yea where the positive and negative to to the motor those solder points are melting when i run it did it with both the original old stinger 20t and the new venom 17t
  3. Replies
    11
    Views
    400

    Well motor wire solder point melted on the motor...

    Well motor wire solder point melted on the motor and im using the connectors like plugs im not sure what theyre called off the top of my head and don't know wire gauge buts its on alot of escs and...
  4. Replies
    11
    Views
    400

    Motor wire melting

    So I have an old old bandit like old enough to have a manual speed control in it but I recently dug it out put a used xl-5 esc in it and bought a venom "modified" 17t motor with a 8.4v 7 cell 5000mah...
  5. Thread: Latest problem

    by Koreyh
    Replies
    23
    Views
    300

    K got it running today it was flooded uh so now...

    K got it running today it was flooded uh so now if its started and sitting still and i open it up like wide open and it hesitates does that mean lsn is lean? or rich
  6. Thread: Latest problem

    by Koreyh
    Replies
    23
    Views
    300

    Is it hard to do?

    Is it hard to do?
  7. Thread: Latest problem

    by Koreyh
    Replies
    23
    Views
    300

    Thanks for the advice on a side note I see people...

    Thanks for the advice on a side note I see people talking about forward only conversion whats good about that? Less stuff to break?
  8. Thread: Latest problem

    by Koreyh
    Replies
    23
    Views
    300

    Yea thats what i was thinking ill try it in the...

    Yea thats what i was thinking ill try it in the morning it was around 35 degrees when i tryed to start and it had a low battery thanks for the replies
  9. Thread: Latest problem

    by Koreyh
    Replies
    23
    Views
    300

    No the ezstart doesnt spin just spins like once...

    No the ezstart doesnt spin just spins like once and everything stops
  10. Thread: Latest problem

    by Koreyh
    Replies
    23
    Views
    300

    Latest problem

    I made a thread about my old 2.5 tmaxx and with your help I got it cleaned and running let it sit for 2 days so I had my friends over and im like look at this and went to start it and it spun for a...
  11. Thread: Old tmaxx 2.5

    by Koreyh
    Replies
    29
    Views
    475

    Do you have to use any special kind of oil cause...

    Do you have to use any special kind of oil cause I think I have some k&n air filter oil in the shop.
  12. Thread: Old tmaxx 2.5

    by Koreyh
    Replies
    29
    Views
    475

    Anything special I need to clean the air filter...

    Anything special I need to clean the air filter with?
  13. Thread: Old tmaxx 2.5

    by Koreyh
    Replies
    29
    Views
    475

    Yea I need to adjust the idle I guess said...

    Yea I need to adjust the idle I guess said something like 1mm idle gap how do I measure that or just guesstimate?
  14. Thread: Old tmaxx 2.5

    by Koreyh
    Replies
    29
    Views
    475

    I went out and ran it some and got it into...

    I went out and ran it some and got it into reverse then almost couldnt get it into forward again probably cause it doesnt want to sit still also do the transmissions on these things use any kind of...
  15. Thread: Old tmaxx 2.5

    by Koreyh
    Replies
    29
    Views
    475

    Ok it had nitro I ran it earlier and got it going...

    Ok it had nitro I ran it earlier and got it going pretty good is the red switch on the controller for reverse? I can't remember but when I stop and flip it nothing changes
  16. Thread: Old tmaxx 2.5

    by Koreyh
    Replies
    29
    Views
    475

    I set the hsn and lsn to what you said gonna go...

    I set the hsn and lsn to what you said gonna go run it see if its better also this morning looked like there was condensation in the tank is that normal? I put the original tank and cleaned it up and...
  17. Thread: Old tmaxx 2.5

    by Koreyh
    Replies
    29
    Views
    475

    Probably what it was since it didnt do it anymore...

    Probably what it was since it didnt do it anymore ill try tuning tomorrow what should I use to turn the lsn since the tank is in the way.
  18. Thread: Old tmaxx 2.5

    by Koreyh
    Replies
    29
    Views
    475

    It was smoking towards the engine but it only did...

    It was smoking towards the engine but it only did it that first time could it be from me soaking it in nitro to clean it out?


    Edit:Its been almost 24hrs out of the nitro so im not sure
  19. Thread: Old tmaxx 2.5

    by Koreyh
    Replies
    29
    Views
    475

    I'll try this tomorrow thanks for the advice it...

    I'll try this tomorrow thanks for the advice it smokes when it gets going when I first ran it today first time in about 4 years it ran I pulled it up and pinched the gas off and looked and it was...
  20. Thread: Old tmaxx 2.5

    by Koreyh
    Replies
    29
    Views
    475

    I ran it some before reading this and when it...

    I ran it some before reading this and when it starts it doesnt want to sit still I have to push up on the trigger on the controller is that normal? Then when I go to take off if I give it full...
  21. Thread: Old tmaxx 2.5

    by Koreyh
    Replies
    29
    Views
    475

    Old tmaxx 2.5

    It's been sitting for 4 years or so and i took the engine off and soaked it in nitro for a few hours to clean it took the tank off and cleaned it out has decent enough fuel lines i think i'm about to...
Results 1 to 21 of 21