Search:

Type: Posts; User: NStampede Freak

Page 1 of 20 1 2 3 4

Search: Search took 0.29 seconds.

  1. Replies
    4
    Views
    95

    You have to realize that the basic tranny design...

    You have to realize that the basic tranny design dates back for more than two decades. Reverse was unheard of on nitros then. Its the reason the stampede/rustler/sport are still fairly inexpensive....
  2. Replies
    7
    Views
    503

    A hammer is a really bad idea...soft brass sleeve...

    A hammer is a really bad idea...soft brass sleeve will deform easily. Heating the block and freezing the sleeve will work every time. It should be by hand ONLY. If hand pressure can't get the sleeve...
  3. Replies
    4
    Views
    95

    No they don't. Transmission is not setup for it...

    No they don't. Transmission is not setup for it like the maxx and revo.
  4. Replies
    10
    Views
    305

    I suspect a lot of these new engine failures are...

    I suspect a lot of these new engine failures are due to people letting them rip on the first few tanks while they are stone cold and have a ton of pinch. High RPMs on a brand new stone cold engine...
  5. Replies
    3
    Views
    68

    A few drops on the OWB is all that is needed. On...

    A few drops on the OWB is all that is needed. On a stock trans, dry is fine since all the gears are plastic.
  6. Replies
    2
    Views
    66

    Anywhere in the low to mid 200's is fine, 280-300...

    Anywhere in the low to mid 200's is fine, 280-300 is getting a bit hot. 300-350 is overheating 350+ and you are in meltdown stage...:fear:
  7. You know what, that is a good idea actually. I...

    You know what, that is a good idea actually. I might just pop on a smaller CB and lower the shift point. It will still be quicker off the line as it would be starting in 1st than a single speed.
  8. Yeah I am thinking about it, I really don't want...

    Yeah I am thinking about it, I really don't want to drop the $$$ on a gray trans but might consider it since the wide ratio is really annoying me.
  9. Close ratio gear set for black trans?

    Hey guys, is there any way to make a close ratio gear set work in a black trans? My maxx has the older 2.5 black trans and it shifts way too wide for my hilly area. It the RPMs just drop down too...
  10. VXL waterproof system FS, $100 shipped.

    http://picturehosting.com/images/NStampedeFreak/vxlsystem.jpg

    Used, but in decent shape. Never was overheated. Wires are not cut in any way. Has factory TRX plug. Some of the blue color is worn...
  11. Replies
    9
    Views
    845

    I probably have that shaft as have plenty of old...

    I probably have that shaft as have plenty of old TQ2 parts laying around if you need.
  12. Replies
    5
    Views
    611

    Reset all end points and dual rates and then go...

    Reset all end points and dual rates and then go back and adjust the end point so the servo just stops at full throttle and doesn't buzz. Take a while but its well worth it.
  13. Replies
    2
    Views
    443

    Engine is locking up from bad fuel sitting in it...

    Engine is locking up from bad fuel sitting in it and the oil is turning to glue/varnish. I have seen it many times. Sometimes by putting some afterrun oil in the carb and turning it over it will free...
  14. Replies
    18
    Views
    738

    Dude, post #12 answered that question exactly.

    Dude, post #12 answered that question exactly.
  15. I think I just answered part of my own question....

    I think I just answered part of my own question. I followed the flow chart and attempted to "reverse direction of shift servo" . When I get to step 4, it says to press meny twice and the LED will...
  16. Enabling channel 3&4 on 2channel TQi, possible?

    Ok, I have torn apart my 2channel TQi and from looking at pictures it seems the only difference over the 4 channel ones is the switches. So I tried jumpering the 3&4 channel pads on the PCB to act as...
  17. I would like to know that as well.

    I would like to know that as well.
  18. Replies
    7
    Views
    1,533

    Tuned pipe, RPM front bumper, and bearings( if...

    Tuned pipe, RPM front bumper, and bearings( if you don't already have them) would be upgrades I would do straight out of the box. I would not do an electric front end as I found them to be much less...
  19. Replies
    5
    Views
    437

    New Era had a pretty nice roll bar for the Nitro...

    New Era had a pretty nice roll bar for the Nitro pede last I checked.
  20. Can traxxas servos handle 7.2V? I would put a 6...

    Can traxxas servos handle 7.2V? I would put a 6 cell RX pack on my maxx if I knew for sure. Maxx trucks need fast strong servos....
  21. Replies
    2
    Views
    514

    Very nice, don't think I have ever seen blue/red...

    Very nice, don't think I have ever seen blue/red bicolor LED before.
  22. Replies
    4
    Views
    538

    Ok, so I got it in and now I see how it works....

    Ok, so I got it in and now I see how it works. The only thing I am wondering is that if there is PC board in the docking station or is it just a wire that goes from the idevice to the plug on the TQi?
  23. Replies
    20
    Views
    4,138

    Just got my TQi today, and overall I like it. I...

    Just got my TQi today, and overall I like it. I never had the TQ 2.4 so I don't know how it was compared to that one, but the features are impressive and a huge step up from the old AM TQs that I...
  24. Replies
    8
    Views
    692

    Yeah, I find that the "flush" setting is very...

    Yeah, I find that the "flush" setting is very lean on the LSN. I tune the LSN by listening to the idle. It should drop down pretty quickly after a WOT run. If it hangs, you are too lean. Also, let...
  25. Replies
    15
    Views
    475

    Nice problem to have...

    Nice problem to have...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4