Search:

Type: Posts; User: mydudrevo

Page 1 of 20 1 2 3 4

Search: Search took 0.19 seconds.

  1. Replies
    6
    Views
    169

    No need to be rude. But as far a polishing sand...

    No need to be rude. But as far a polishing sand with 1200-2000 grit wetsand paper and polish with a good compound. Are you going to polish the epoxy or the clear you sprayed over everything?
  2. Replies
    24
    Views
    2,245

    *** My 9 Revo Bash Videos ***

    I would like to know why my post was deleted? There was no reason to delete it. It was a nice post saying how seeing this thread brought me back to being a kid again and watching these videos. ...
  3. Replies
    14
    Views
    256

    The losi 3.4 does not require a big block mount....

    The losi 3.4 does not require a big block mount. The only issue is the crankshaft is 3mm to long so you shave it down and your good to go.

    If someone doesn't want to have to do minor mods I can...
  4. Replies
    14
    Views
    256

    Picked up a Revo

    Losi 3.4 would be a great and relatively cheap motor that is basically identical to the 3.3 but with a bit more power and holds a better tune. They can be found on eBay for pretty cheap.
    ...
  5. I've tried most shafts available, stock, traxxas...

    I've tried most shafts available, stock, traxxas Cvds, lst2 Cvds, and some of the eBay junk but the best shaft is the summit shafts by a long shot, I wasted so much money until I finally tried the...
  6. The ones on their website look to be a completely...

    The ones on their website look to be a completely different design.
    http://eracingpro.com/shop/894-frontrear-u-joint-slider-drive-shaft-swing-axle-cvd-for-t-maxx-33-revo-25-33-e-revo.html
  7. Replies
    50
    Views
    1,374

    Big blocks hold a tune much better and are much...

    Big blocks hold a tune much better and are much are not as sensitive to changes in humidity and temperature. This has been my experience anyways.
  8. Replies
    38
    Views
    553

    I was just saying 3.85 is way to high for Lvc I...

    I was just saying 3.85 is way to high for Lvc I set mine to 3.4, I have packs that are 3 years old still getting regularly used. I wasn't trying to mislead the op but trying to give him the...
  9. Replies
    38
    Views
    553

    This is wrong. The can not drop below 3.0v per...

    This is wrong. The can not drop below 3.0v per cell. 3.85 is storage voltage. Safely 3.2v per cell is a common low voltage cutoff setting. Honestly please do lots of research and make sure you...
  10. Replies
    38
    Views
    553

    You can not run them below 3v per cell. I don't...

    You can not run them below 3v per cell. I don't let mine go any lower than 3.4v per cell. Also storage charge them before you let them sit
  11. Replies
    15
    Views
    483

    Ya Galveston is pretty nasty right now I live...

    Ya Galveston is pretty nasty right now I live 30mins away and the seaweed is worse than I've ever seen
  12. Replies
    2
    Views
    114

    This has already been covered in your other...

    This has already been covered in your other thread. Try not to create multiple threads for thee same question
  13. Replies
    25
    Views
    250

    Check you rotor while your at it it could have...

    Check you rotor while your at it it could have delaminated
  14. Replies
    25
    Views
    250

    It sounds like 2 of your 3 motor wires are...

    It sounds like 2 of your 3 motor wires are touching somewhere wether it be inside the motor or outside. I've had this happen and that's exactly what your describing.
  15. Replies
    30
    Views
    1,058

    Is that lexan or p.e.t.g.

    Is that lexan or p.e.t.g.
  16. You could just polish the crank and that would...

    You could just polish the crank and that would give a little extra performance. Just don't touch the areas where the bearings go you can easily take of enough material to cause a bearing leak
  17. There's no need to pull the piston to clean the...

    There's no need to pull the piston to clean the motor IMO usually going to cause more issues than it's worth.
  18. How did that happen. Did you recently rebuild it

    How did that happen. Did you recently rebuild it
  19. Sounds like you clutch spring broke. When the...

    Sounds like you clutch spring broke. When the clutch spring breaks it doesn't hold the clutch in at idle causeing it to stall out unless it's moving. Very common problem. Upgrading to a 3 show clutch...
  20. Replies
    10
    Views
    344

    I'm sorry to say but there is no way you can get...

    I'm sorry to say but there is no way you can get 25-30 mins on a 4600 mah battery unless you are going very slow and in your lid a lot. Pretty much every competitive sc drive only gets about 10 mins...
  21. Replies
    10
    Views
    344

    This is very true. On a track at race pace I only...

    This is very true. On a track at race pace I only get 10 mins out of a 7200. So it really depends on style of driving
  22. Replies
    68
    Views
    3,254

    It's a great budget motor and all but impossible...

    It's a great budget motor and all but impossible to kill. That motor just loves 3s and can even handle the occasional 4s speed run.
  23. Replies
    68
    Views
    3,254

    I don't know why they dont just put the castle...

    I don't know why they dont just put the castle 3800 in it and anodize it blue with a traxxas label on it. Just like the 2400/2800 rebranded castle motors losi and traxxas are already using.
  24. Thread: shock towers

    by mydudrevo
    Replies
    4
    Views
    114

    I've put my truck through more than I thought I...

    I've put my truck through more than I thought I ever could and it just comes back for more. I've broken 1 arm (then upgraded to rpm up front) and that's it the slash 4x4 is a very very tough truck...
  25. Replies
    68
    Views
    3,254

    Idk just seems that traxxas would want is to know...

    Idk just seems that traxxas would want is to know that they upgraded to 4 pole
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4