Search:

Type: Posts; User: CobraWasHere

Page 1 of 20 1 2 3 4

Search: Search took 0.26 seconds.

  1. Replies
    90
    Views
    5,565

    Jimbo once mentioned that any aftermarket servo...

    Jimbo once mentioned that any aftermarket servo saver was a waste and worse than stock.
  2. Replies
    232
    Views
    4,172

    I just mean that I wouldn't spend money on...

    I just mean that I wouldn't spend money on something that most likely doesn't need replacing.
  3. Replies
    232
    Views
    4,172

    JSmith, I didn't use the 5700kv long or hard...

    JSmith, I didn't use the 5700kv long or hard enough to have weakened the magnets... it would be silly to replace them.
  4. Replies
    42
    Views
    1,212

    you guys are silly, 100% punch control means that...

    you guys are silly, 100% punch control means that it's limiting the punch as much as possible... 0% means there's no punch limiting. Don't run a drag brake unless you like to heat things up, and a...
  5. Ah, I see. Thanks!

    Ah, I see. Thanks!
  6. Thread: Bearings?

    by CobraWasHere
    Replies
    63
    Views
    1,262

    The most useful upside to using ceramic bearings...

    The most useful upside to using ceramic bearings in a non-race setting is that when properly maintained, they will last longer. Ceramics are more smooth, more heat resistant, more shatter resistant,...
  7. It was supposed to be a reply to Jimbo

    It was supposed to be a reply to Jimbo
  8. Thread: Bearings?

    by CobraWasHere
    Replies
    63
    Views
    1,262

    Here's a good read:...

    Here's a good read: http://www.bearingkinetics.com/ceramic-bearings.htm
  9. Thread: Bearings?

    by CobraWasHere
    Replies
    63
    Views
    1,262

    Most of the mods you can do to a merv will yield...

    Most of the mods you can do to a merv will yield results that are probably not noticeable over stock. It's unlikely that you'll notice a difference with bearings unless using a broken bearing vs an...
  10. ...which is what forces the car to slide rather...

    ...which is what forces the car to slide rather than to grip and traction roll. Why do you think full scale drift cars don't have long travel suspensions, but rather nearly slammed-to-the-ground...
  11. Replies
    16
    Views
    451

    Running dual servos without setting them up...

    Running dual servos without setting them up properly is worse than running a single servo. Just stick with a single ******* or BlueBird 390.
  12. Replies
    18
    Views
    725

    That works too, but I didn't have any putty...

    That works too, but I didn't have any putty...
  13. Use rally shock limiters on your Merv... traction...

    Use rally shock limiters on your Merv... traction rolling is its biggest downfall IMHO.
  14. Replies
    18
    Views
    725

    Or... start with less lead tape than you need,...

    Or... start with less lead tape than you need, and add more until you've achieved balance of your wheel!
  15. Jimbo, won't stiffer springs cause the car to...

    Jimbo, won't stiffer springs cause the car to slide rather than traction roll?
  16. Replies
    12
    Views
    419

    Definitely step down to 2s.

    Definitely step down to 2s.
  17. Replies
    12
    Views
    419

    It sounds like you still have three days to go...

    It sounds like you still have three days to go out and buy a temperature gun!
  18. Replies
    232
    Views
    4,172

    Jimbo, I've been running sweepracing's belted...

    Jimbo, I've been running sweepracing's belted radials for a 1/8 GT car on my vorza and they're killer.
  19. Replies
    8
    Views
    335

    Eh, I always use a Dynamite balancer with some...

    Eh, I always use a Dynamite balancer with some lead tape. Sure, it costs money and most people say they can balance without one, but I preferred using one. The street radials on my Vorza got up to...
  20. Replies
    23
    Views
    638

    Chefmike, all you need to do to raise the height...

    Chefmike, all you need to do to raise the height with the limiters in is to extend the pushrods in both the front and rear. Making them longer (and I can see that yours are adjustable) will raise...
  21. Replies
    9
    Views
    341

    amainhobbies has dirt hawg Is for $12 a pair.

    amainhobbies has dirt hawg Is for $12 a pair.
  22. Replies
    22
    Views
    732

    If anything I'd get the delrin ones made by...

    If anything I'd get the delrin ones made by Driven Productions.
  23. Replies
    27
    Views
    1,276

    I've got a used full T-Bone setup that I'll sell...

    I've got a used full T-Bone setup that I'll sell and ship. Complete with the wheelie bar. Their stuff has a lifetime warranty, so if it breaks, you just send them a pic, then they ship you a...
  24. Replies
    450
    Views
    15,224

    Mossie, since those foams weigh much less and...

    Mossie, since those foams weigh much less and have less diameter, you can afford to gear 35/45. The car will be slower using foams without gearing up.
  25. Replies
    92
    Views
    4,606

    I destroyed my gyro within 5 minutes of having it...

    I destroyed my gyro within 5 minutes of having it in my Vorza. My servo browned out (got a BEC since to fix that) and hit a curb doing 30mph or so, which forced the batteries (which are enormous...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4