Search:

Type: Posts; User: zdragon71

Page 1 of 8 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    34
    Views
    1,423

    Wow! That is the best looking paint job ive seen...

    Wow! That is the best looking paint job ive seen yet on an RC. Great job!!!
  2. Replies
    26
    Views
    598

    Youve got a 36 tooth spur. Its the same size as...

    Youve got a 36 tooth spur. Its the same size as the slipper clutch. If you go up a couple of teeth it will give you more adjustment. Get a 38 or 40 tooth spur gear and you will have plenty of room...
  3. Replies
    26
    Views
    598

    What tooth count are you running on spur and...

    What tooth count are you running on spur and bell? I had the same issue with a 36 tooth spur and 15 tooth and 17 tooth bell. I had to go back to a 38 to 40 tooth spur gear.
  4. Replies
    12
    Views
    619

    It will be fine. Just when you shut it down after...

    It will be fine. Just when you shut it down after first tank turn the flywheel so that the piston is at bottom dead center. This is because when the engine cools if the piston is at top dead center...
  5. Thread: 2075 servos

    by zdragon71
    Replies
    8
    Views
    467

    +1^^^ i would get a couple of Savox with at least...

    +1^^^ i would get a couple of Savox with at least 100in oz torque rating. Metal or titanium geared digital. If not savox i recommend futuba or hitech metal geared servos. Never try to save money by...
  6. Replies
    7
    Views
    433

    Blue wire to plug yellow wire grounds to engine...

    Blue wire to plug yellow wire grounds to engine mount bolt. Wand ignitor will not work if yellow wire is not grounded.
  7. Replies
    44
    Views
    2,349

    Nice! They do look better black. I like em

    Nice! They do look better black. I like em
  8. Replies
    44
    Views
    2,349

    http://img.tapatalk.com/471ffffc-a4d0-7a45.jpghttp...

    http://img.tapatalk.com/471ffffc-a4d0-7a45.jpghttp://img.tapatalk.com/471ffffc-a4e5-590a.jpg
    This is my 5310 short chassis revo. Pretty much stock except the front a-arms are RPM and the shocks are...
  9. Replies
    3
    Views
    1,168

    Yes you need all the on board sensors for...

    Yes you need all the on board sensors for whatever you want to monitor. Gps for speed, temp wire around head fir temps, and voltage sensor for voltage.
  10. If you reverse the above statement and run 100 in...

    If you reverse the above statement and run 100 in front and 50 in rear it will help oversteering a bit. In other words it helps the front end to pull better through corners.
  11. Replies
    8
    Views
    735

    I drilled my factory blue revo stinger out to 1/4...

    I drilled my factory blue revo stinger out to 1/4 inch and noticed a nice difference. Be careful and not more than 1/4 inch or you will chance breaking off the stinger. I have recently installed the...
  12. Replies
    4
    Views
    326

    That should fix the engaging issue you had. Also...

    That should fix the engaging issue you had. Also would explain the noise you started to hear. Good find and fix.
  13. Thread: Foc

    by zdragon71
    Replies
    6
    Views
    290

    When i made my revo forward only i noticed a big...

    When i made my revo forward only i noticed a big difference in take off and top end speed. Its like i geared it different. Then when i did change the gearing as well my 2.5R revo is as fast as my...
  14. Replies
    4
    Views
    326

    Sounds like you may have stripped a few teeth off...

    Sounds like you may have stripped a few teeth off the spur gear. Its a commonly broke part. The spur gear that is. As far as adjusting it you need to take a 2mm hex wrench and stick it down into the...
  15. Hsn 4 turns out and lsn 2 turns out with 1mm idle...

    Hsn 4 turns out and lsn 2 turns out with 1mm idle gap.
  16. Thread: VXL gearing

    by zdragon71
    Replies
    12
    Views
    297

    Yeah if you dont want to tune every time you run...

    Yeah if you dont want to tune every time you run then you may want to go electric. For the best engine performance and longevity you need to keep your screwdriver in pocket and adjust hsn everytime...
  17. Tape? You do know what and where your...

    Tape? You do know what and where your differentials are right? Shouldnt be no tape holding them together.
  18. Replies
    11
    Views
    764

    Nice choice on the tires and bead locks!

    Nice choice on the tires and bead locks!
  19. Keep in mind also if its not a trim or servo horn...

    Keep in mind also if its not a trim or servo horn problem you could possibly have a bad servo all together. Whenever my throttle brake servo went out on me it went WOT without me touching anything....
  20. Replies
    3
    Views
    387

    I cut my entire windshield out and hald the back...

    I cut my entire windshield out and hald the back window also a much larger area around engine. It makes a huge difference considering these engines are air cooled. Besides the oil in fuel for...
  21. Replies
    389
    Views
    25,016

    Thats one good looking truck!! Love it

    Thats one good looking truck!! Love it
  22. Replies
    636
    Views
    41,039

    Great job Snookman! Cant wait to see the bet...

    Great job Snookman! Cant wait to see the bet winning run now.
  23. Replies
    9
    Views
    354

    You can just adjust the linkage so it has slack...

    You can just adjust the linkage so it has slack in the brakes and doesnt engage so hard
  24. Replies
    26
    Views
    1,297

    Just keep it rear mount and get the revo platinum...

    Just keep it rear mount and get the revo platinum header that is spring mount. Being spring mounted it wont break like the stock bolt mount header. If you get it make sure to buy the spring and new...
  25. Replies
    9
    Views
    354

    The tmaxx requires a higher torque servo on...

    The tmaxx requires a higher torque servo on steering anyways. But saying that ive got a 2075 servo on my throttle and brake and never had any issues bending my pads with 125 in oz of torque. So as...
Results 1 to 25 of 192
Page 1 of 8 1 2 3 4