Search:

Type: Posts; User: TheBlakester419

Page 1 of 3 1 2 3

Search: Search took 0.11 seconds.

  1. Replies
    4
    Views
    168

    Check your servo, screws, and all of the hardware...

    Check your servo, screws, and all of the hardware attached to them. Tighten some screws and check for stripped screws.
  2. Replies
    3
    Views
    206

    New motor

    I recently burned up my stock motor and am looking to upgrade. What is a good upgrade if I am only going to be using NIMH batteries and on a budget?
  3. Replies
    3
    Views
    176

    How do I prevent this in the future?

    How do I prevent this in the future?
  4. Replies
    3
    Views
    176

    Motor shaft

    The set screw on the pinion gear has routed out a groove on the motor shaft and has made multiple indentions on the shaft, also. I think I may have over tightened the screw. Is there any way to fix...
  5. Replies
    16
    Views
    322

    It does stutter with the noise

    It does stutter with the noise
  6. Replies
    16
    Views
    322

    Ok thanks for all of your help. It's greatly...

    Ok thanks for all of your help. It's greatly appreciated.
  7. Replies
    16
    Views
    322

    Will it hurt it if I leave it or should I find a...

    Will it hurt it if I leave it or should I find a way to fix it?
  8. Replies
    16
    Views
    322

    I can not replicate the noise any way at all....

    I can not replicate the noise any way at all. Only by putting a slight amount of throttle. I tightened the motor mount screws, and it is still making the noise.

    Could the spur gear being offset be...
  9. Replies
    16
    Views
    322

    I removed the slipper clutch to replace the spur,...

    I removed the slipper clutch to replace the spur, and did a thorough cleaning while it was out. It was clicking before and after this. It has been clicking like this since I got it. It stutters and...
  10. Replies
    16
    Views
    322

    Clicking noise

    I have a completely stock Slash 4x4 that has been making a clicking noise when I put slight throttle on, but goes away at a certain point. It does not do it when I roll it, and I can not figure it...
  11. Replies
    13
    Views
    346

    Get the Duratrax Flashpoint infrared temp gauge....

    Get the Duratrax Flashpoint infrared temp gauge. It's $25 on amazon.com and is very small, with a lanyard you can put around your wrist. It's even small enough to fit in your pocket and not notice it...
  12. Replies
    7
    Views
    442

    It is an Integy

    It is an Integy
  13. Replies
    7
    Views
    442

    Heatsink or no?

    I have a motor fan/heatsink combo, but the fan just quit working. Should I put the heatsink without the fan on the motor, or leave the motor the way it is, without anything on it? Thanks
  14. Replies
    9
    Views
    372

    Sorry if its a stupid question, but what does LCG...

    Sorry if its a stupid question, but what does LCG stand for? (I'm guessing low center of gravity)
  15. Replies
    15
    Views
    1,294

    everything is good

    everything is good
  16. Replies
    15
    Views
    1,294

    blades are in perfect condition

    blades are in perfect condition
  17. Replies
    15
    Views
    1,294

    Stability Problems (QR-1)

    No matter what I do, I cannot get the QR-1 to stay stable. I have reset the gyro, and recalibrated it on the most level surface I know of. I even turned off the air conditioning and closed all of the...
  18. I run the big bore stock springs with thick...

    I run the big bore stock springs with thick spacers on both. I would reccomend slightly stiffer shocks than the ones that come with the big bore shocks. Try some different spacers out and if you like...
  19. Replies
    15
    Views
    1,279

    mine may be a 60 footer...

    mine may be a 60 footer...
  20. Replies
    191
    Views
    48,272

    Sticky: Do you live near Katy RC? Thats my favorite track...

    Do you live near Katy RC? Thats my favorite track to go to. There is a hobby shop in Sugarland that has a good beginner's track.
  21. Replies
    191
    Views
    48,272

    Sticky: What part of Katy do you live in?

    What part of Katy do you live in?
  22. Replies
    15
    Views
    1,279

    https://lh4.ggpht.com/21yz6Ub34CEqior9jkUFxlnu69W7...

    https://lh4.ggpht.com/21yz6Ub34CEqior9jkUFxlnu69W7hN7vyejU4Fc4AsvTWSAqVA2s_etwlro60AfK0NsF17M=s114https://lh6.ggpht.com/Nl2RtFA0Aj7fwkeCYlq4-v5N2_bkMF-https://lh6.ggpht.com/QaI1RcB-6Evvt36guyzQattXrQF...
  23. Replies
    15
    Views
    1,279

    I'm using the digital camo duct tape too. Did you...

    I'm using the digital camo duct tape too. Did you go from side to side or back to front? Is it one long strip or did you break it up? And nice job btw. If I didn't know it was duct tape I would've...
  24. Replies
    15
    Views
    1,279

    Duct Tape

    I am looking to duct tape my stock slash 4x4 body. I saw one post that had a duct taped Ford body. Does anybody have any tips on how to do it? Thanks
  25. Thread: Motor

    by TheBlakester419
    Replies
    0
    Views
    144

    Motor

    Which motors can I put in the blast without changing anything else?
Results 1 to 25 of 53
Page 1 of 3 1 2 3