Search:

Type: Posts; User: hondarider450

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    0
    Views
    72

    programming esc?

    i dont know if this is the right place to post this so let me know if it should go somewhere else

    i am having trouble with the vxl-3s. i just purchased a dynamite fuse 4800kv motor from my LHS. It...
  2. Replies
    4
    Views
    613

    I don't really have the $$$ for the 2.4 system,...

    I don't really have the $$$ for the 2.4 system, just spent most of it on the vxl system. I will try the different set of crystals. It's just weird that one day it was fine and the next day it was...
  3. Replies
    4
    Views
    613

    And if it helps I have the original 27MHz radio...

    And if it helps I have the original 27MHz radio system
  4. Replies
    4
    Views
    613

    bad signal

    Went to run the brushless jato today and for some reason it had a very bad signal. It would only reach about 30 yards or so and then hesitate a lot and lose signal. A couple times it actually took...
  5. Replies
    13
    Views
    6,817

    I am having trouble locking the trans into 2nd...

    I am having trouble locking the trans into 2nd gear. I have done it once already to my jato so I know the theory on how to do it, but it seems like there is something binding up inside cause it makes...
  6. Replies
    4
    Views
    377

    velineon 3500

    Not sure if this is the right place to post it but would the traxxas velineon 3500 be too small to put on a t-maxx? I wasn't sure if it would overheat it being as the truck and tranny is 4WD and the...
  7. If you're good with a dremel/drill/saw etc. you...

    If you're good with a dremel/drill/saw etc. you can make your own motor mount. I made my own and it works great, was even able to make the oval/banana shaped hole used for adjusting the motor. i dont...
  8. I agree. If you use the motor mount from the...

    I agree. If you use the motor mount from the EMaxx I would recommend adding something for more support, especially with only the 2 screws from the clutch guard holes. If you upgrade to the aluminum...
  9. Replies
    25
    Views
    3,073

    yeah that problem im having with mine is that i...

    yeah that problem im having with mine is that i dont have a top plate. i stripped everything off to lower the CG. so now im doing what you did with your other one and mounting everything to the...
  10. Replies
    25
    Views
    3,073

    is there an advantage to using the angled servo...

    is there an advantage to using the angled servo mount? the servo is what i am having the most trouble with. thanks again this will be a big help
  11. Replies
    25
    Views
    3,073

    if you dont mind me asking, how did you mount...

    if you dont mind me asking, how did you mount your ESC, receiver, and steering servo? pics of the front mounts would help alot if you have them just so i can get an idea. I just did the brushless...
  12. Replies
    6
    Views
    766

    Slipper clutch is adjusted good. I think I may...

    Slipper clutch is adjusted good. I think I may have a defective battery. I tried my cousins battery and it worked great
  13. Replies
    13
    Views
    262

    No its not in training mode neither is the low...

    No its not in training mode neither is the low voltage detection on. I'm beginning to think I got a defective battery because after putting it on the charger again it seemed to work fine, but the...
  14. Replies
    13
    Views
    262

    Thanks I will try that. I'm new to the brushless...

    Thanks I will try that. I'm new to the brushless stuff so I would've never thought of to try that
  15. Replies
    13
    Views
    262

    The thing I don't get is why does it sometimes...

    The thing I don't get is why does it sometimes run with low power as soon as I start running it? Even if its been sitting all night and first thing in the morning I go to drive it and it runs poorly...
  16. Replies
    13
    Views
    262

    Well the thing is I just spent over $100 on the...

    Well the thing is I just spent over $100 on the battery and charger and don't have much more to work with. Would the lipos lower the running temps or did I just read the wrong?

    And what would you...
  17. Replies
    6
    Views
    766

    Yeah I locked it in 2nd gear. Sometimes it will...

    Yeah I locked it in 2nd gear. Sometimes it will run good, but sometimes it will run and all of a sudden lose power and run very slowly. One time it ran with low power right from the get go before it...
  18. Replies
    13
    Views
    262

    that makes sense. what would cause it to lose...

    that makes sense. what would cause it to lose power and run very slowly? sometimes it will run fine, and sometimes it will run with low power as soon as i start driving it. at first i thought it was...
  19. Replies
    13
    Views
    262

    sorry if i steal your thread thats not my...

    sorry if i steal your thread thats not my intention, im just trying to get some more knowledge. but do you guys choose your gearing by the temp that the motor runs at? im new to this brushless stuff...
  20. Replies
    6
    Views
    766

    Anyone have an idea? I also just put in a 9.6V...

    Anyone have an idea? I also just put in a 9.6V 8cell in it if that makes a difference.

    Sorry if this isn't the right section. If I need to post this somewhere else let me know being as the jato...
  21. Replies
    6
    Views
    766

    gear ratio not right?

    The guy at the hobby store gave me a 17 pinion and 65 spur for my brushless conversion that made a 3.8 gear ratio. Is that too big of a spur gear? It's the velineon 3500 and vxl-3s. I just ran it...
  22. Replies
    22
    Views
    1,614

    That is clean, i like the setup and location of...

    That is clean, i like the setup and location of everything. How did it handle with the way the weight is distributed?
  23. Replies
    22
    Views
    1,614

    I don't think the epoxy came loose. As soon as I...

    I don't think the epoxy came loose. As soon as I put the transmission together it didn't have reverse, I just thought it was normal because it didn't have reverse before. It works perfectly in...
  24. Replies
    22
    Views
    1,614

    Thanks, I have not been able to run it yet but...

    Thanks, I have not been able to run it yet but once I relocate the esc, receiver, and battery I will definitely post a vid and let you know how it handles. I'm also getting new tires so that will...
  25. Replies
    22
    Views
    1,614

    That's basically what i saw on the YouTube video....

    That's basically what i saw on the YouTube video. As for the pin method in the clutch, I did it with epoxy, but will not go in reverse. Why does it work with the pins but not the epoxy? And can I...
Results 1 to 25 of 34
Page 1 of 2 1 2