Search:

Type: Posts; User: revo_stevo

Search: Search took 0.16 seconds.

  1. Replies
    14
    Views
    551

    pure nonsense

    I had left this forum a few years back because of people with "smart pants" ..same thing same person on my first question when I decided to stick my nose back into this forum..I liked coming here. I...
  2. Replies
    20
    Views
    759

    Push and hold reset button until it links green 2...

    Push and hold reset button until it links green 2 times then let off the button..pull full throttle and hold it until light blinks three times..then let trigger go to neutral..after a few seconds...
  3. Thanks for all of both of you guys help. I can...

    Thanks for all of both of you guys help. I can see how I have you lost but bottom line is the last few sentences you said period ..if its not right gonna go bad lots faster that simple...
    Again...
  4. Something to ponder ...I measured the amount the...

    Something to ponder ...I measured the amount the clutch bell can travel..first conversion of mm to in. 1mm is .039 in. Mine was .030...then specked the mesh between the spur and clutch bell... It was...
  5. :) I think I hit the v or the b Thinking I...

    :)


    I think I hit the v or the b Thinking I hit the space bar ..lot of times my mind is three sentences ahead of my typing lol ; )
  6. I'm gonna check all this very thoroughly hoping...

    I'm gonna check all this very thoroughly hoping to find a problem a answer..thanks for all thevinput..
  7. Replies
    11
    Views
    448

    Could be a problem ...here's what I did with the...

    Could be a problem ...here's what I did with the exchange program ..I had run about 15 gallons through my 3.3 when the con rod broke..but it cracked the block and broke the crank. I didn't feel like...
  8. Since I've never went down that road let me ask...

    Since I've never went down that road let me ask this...is a lighter cb ot a heavier cb the best way to go..the light one obviously had a lot of opening to slow sir inn..the heavier one does...
  9. I'm sure he is..I'm not mad at all I ask for...

    I'm sure he is..I'm not mad at all I ask for advice..there's two ways to do that ..I appreciatevthe advice from anybody because the more I hear the more I rule out...both you give me good advice..and...
  10. How much play should the clutch bell have? Or...

    How much play should the clutch bell have? Or movement ..I take all things said into consideration ..for example oomp days frame maybe tweaked..never crashed or hit anything to cause this. Remember...
  11. Replies
    4
    Views
    272

    What I did was tighten it down not hard just do u...

    What I did was tighten it down not hard just do u know its all the way ..all act and shift differently..make 1/4 turns at a time. It will start shifting long first. Keep 1/4 turns until u get it...
  12. U The motor normally runs 230-240 degrees ...I...

    U

    The motor normally runs 230-240 degrees ...I have to assuming the mesh is right I'm running the same spur gear that came on it new.. and it still looks good..I've been doin this quiet a while...
  13. Replies
    21
    Views
    539

    Also TRAXXAS has motor replacement for $110.00...

    Also TRAXXAS has motor replacement for $110.00 with warranty on a brand new motor.
    Just to let you know
  14. clutch bearings wear out faster than the clutch

    I have messed with nitro rc vehicles for 10+ years. I'm on my 2nd 3.3 motor in my revo and the clutch bearings just aren't holding up long at all. Both motors exsct same thing. Before I can wear out...
  15. Replies
    2
    Views
    235

    Same problem here...I bypassed the opti drive and...

    Same problem here...I bypassed the opti drive and adjusted it in after killing 4 servos...I know not to shift unless I'm stopped..no problems since
  16. Thread: Bell clutch

    by revo_stevo
    Replies
    11
    Views
    296

    What I found to work real good use the 4146x...

    What I found to work real good use the 4146x spring with aluminum 2 piece shoes.scant west them out and hooks solid fast..
    What I need to know is how to keep from eating up clutch bearings...any...
Results 1 to 16 of 17