Search:

Type: Posts; User: cliffdawg

Page 1 of 3 1 2 3

Search: Search took 0.16 seconds.

  1. Replies
    12
    Views
    1,336

    I put the hardened stuff in to play it safe. I...

    I put the hardened stuff in to play it safe. I got pics of my trucks up on forum. Just search big joes and me...
    Ryan
  2. Replies
    12
    Views
    1,336

    I did that exact setup!!!! hahahahh... Kept it...

    I did that exact setup!!!! hahahahh... Kept it pretty stock, except robinson harden steel gears. I bent the tierods a few times because of the extra strain on the truck (I think) I love the setup it...
  3. Thread: ball holders

    by cliffdawg
    Replies
    2
    Views
    548

    ball holders

    Hello everyone,

    I was wondering if anyone has done this. Replaced the dust cover retainers that hold the ball ends in place at the end of the A-arms with T-MAXX ones. A T-Maxx owner told me that...
  4. Replies
    13
    Views
    1,118

    Power up link system?

    Does anyone know if Traxxas is going to do power up with the link system in the near future? Also is the Link that much better of a transmitter then the 2.4??? I have multiple rc vehicles too.
    Ryan
  5. Replies
    21
    Views
    1,383

    Note: Most stainless is a little softer then...

    Note: Most stainless is a little softer then grade 5.
  6. Replies
    6
    Views
    290

    My truck blows a bit of smoke even at idle...

    My truck blows a bit of smoke even at idle though. I will try richening the lsn. The Idle screw should be adjusted in 1/16?
  7. Replies
    6
    Views
    290

    Creeping Forward

    So I just replaced my clutch shoes. They were very badly warn down, (they were oval in shape one shoe was broken at the flywheel pin and the 90 degree sidewalls of the shoe was cut with a 45 degree...
  8. Replies
    11
    Views
    596

    wareagle, do you have a paypal? and how much are...

    wareagle, do you have a paypal? and how much are you looking for that piece? also those are stock trx bearings? and no fuel has been run through that block?

    Alex, thanks for the offer. I really...
  9. Replies
    11
    Views
    596

    so you have a new block with stock trx bearings...

    so you have a new block with stock trx bearings and you wanna sell it?
  10. Replies
    11
    Views
    596

    Is it hard to pull the crankcase bearings out?

    Is it hard to pull the crankcase bearings out?
  11. Replies
    11
    Views
    596

    Going to replace my engine bearings...

    So I have a 3.3 with 2.5 gallons run through it, and I have always had alot of fuel coming through the bearing by the flywheel. It was never really a tuning issue until recently. More recently I have...
  12. Replies
    39
    Views
    1,713

    bent my chassis last year. Shattered the rear...

    bent my chassis last year. Shattered the rear bulkhead and ripped up some rear end stuff. Took the chassis off and bent it back, replaced the broken stuff, and my truck was back to normal. (I dont...
  13. Replies
    5
    Views
    391

    so... Next question. I have that big meat on the...

    so... Next question. I have that big meat on the wheels, and I have a somewhat powerful servo to move them, What should I do with the reviever pack? Go Traxxas pack? Stick with Alkalines and throw...
  14. Replies
    5
    Views
    391

    20 ft jumps, a must. I have an awesome BMX track...

    20 ft jumps, a must. I have an awesome BMX track in the next town over. So I really jump the smack out of my revo. Thicker shock oil is a good call. Put 50W in yesterday, thinking thats not enough.
    ...
  15. Replies
    5
    Views
    391

    So I ended up rebuilding the whole truck today,...

    So I ended up rebuilding the whole truck today, went with a 40 tooth spur gear and a 14t CB. Both in Integy. I put new clutch shoes in and A Hobbico MG c-70 for steering that big meat on the big joe....
  16. Replies
    8
    Views
    406

    Went to LHS, they did not have the shims... So I...

    Went to LHS, they did not have the shims... So I took the traxxas shim and sanded it with emery cloth, and that worked. Now I have no more binding. Thank you for the help guys.

    Ryan
  17. Replies
    8
    Views
    406

    thank you very much!!! This forum and its members...

    thank you very much!!! This forum and its members are some of the best.

    Ryan
  18. Replies
    8
    Views
    406

    Is that my only option? Or is that just the best...

    Is that my only option? Or is that just the best option?

    Thanks,
    Ryan
  19. Replies
    8
    Views
    406

    Integy clutch bell issue...plz help

    Hey guys... Just bought an integy clutchbell, on reinstall (on 3.3) there is a shim in between the eclip and bearing on the stock CB. Do I use the traxxas shim with the integy??? they dont include...
  20. Replies
    5
    Views
    391

    Winter build with 40 series

    So I bought my 40 series stuff in the fall (axial beadlocks and big joes) I only took it out once after install. A few things, lost some top end and my shift point needed adjustment. Engine temps...
  21. Replies
    10
    Views
    506

    I am having the same problem. Did the cleaning of...

    I am having the same problem. Did the cleaning of the OWB fix this issue? If so can I soak it in simple green?? thanks. Also can I use grease to lube the bearing or do I have to use marvel mystery...
  22. can you tell me, who you ordered them from???

    can you tell me, who you ordered them from???
  23. how much did you spend on that servo? and if I...

    how much did you spend on that servo? and if I dont have a digital system what would be a good option?
  24. yeah, I am pretty sure the new servo is on the...

    yeah, I am pretty sure the new servo is on the way, have the traxxas digital now but it will prob. burn out soon. Then I will put a nice metal gear steering servo in. Metal steering servo suggestions...
  25. Sorry about the wording, its been updated. Ryan

    Sorry about the wording, its been updated.
    Ryan
Results 1 to 25 of 74
Page 1 of 3 1 2 3