Search:

Type: Posts; User: earthmover

Page 1 of 4 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    23
    Views
    599

    That i understand..... but if I buy a 75mhz...

    That i understand..... but if I buy a 75mhz receiver other then airtronics and the same channel crystal will they talk to each other?
  2. Replies
    23
    Views
    599

    matching radio to receivers

    I have a MX-3 on channel 69. What do I need to get my tmaxx to work with that radio? Someone told me everything had to match so I am not too sure what they were referring too. Was it the...
  3. Replies
    1,142
    Views
    608,428

    Sticky: webshots...

    webshots
  4. Thread: wheelie bar

    by earthmover
    Replies
    3
    Views
    157

    wheelie bar

    checkout my self made wheelie bar..... not as good looking as Swami's but serves the purpose.

    http://community.webshots.com/album/93015044MmsiEe
  5. Thread: Xtm

    by earthmover
    Replies
    4
    Views
    251

    the kit comes with everything you need.... i did...

    the kit comes with everything you need.... i did remove the reverse cause the engine would jerk it pretty hard.... i run a 16 clutch bell because i like the low end power..... no metal gears just...
  6. Thread: Xtm

    by earthmover
    Replies
    4
    Views
    251

    had mine for almost a year now..... still with...

    had mine for almost a year now..... still with the first glow plug!!!
    heres a pic of the conversion


    http://community.webshots.com/user/earthmover101
  7. Replies
    4
    Views
    337

    MY tmaxx pics

    http://community.webshots.com/user/earthmover101
  8. Replies
    3
    Views
    189

    question on idler

    I have a novak brushless and I just blew my idler.... the traxxas book said not to use an aluminum idler 1996x with the steel top gear 3195. Do you need to change out the 3195 to a 3195x too?
  9. you have to gear down if you read my earlier...

    you have to gear down if you read my earlier post on the different gearing you will notice that the slightest pinion change makes a huge difference in speed and torque. and this rusty kills my...
  10. Replies
    13
    Views
    435

    If your using the stock servo change it out. ...

    If your using the stock servo change it out. Mine was twichy and could not hold a straight line either. (maybe your problem)

    I use a hitec hs-5945mg great holding power and huge torque...
  11. Thread: wheelies

    by earthmover
    Replies
    15
    Views
    442

    SO TRUE...... wheelies are great to show off...

    SO TRUE...... wheelies are great to show off with and please the kids..... not practical for everyday......... but theres nothing better then going out to an r/c track and having the capabilities of...
  12. I am using dirt hawg tires..... used a stop...

    I am using dirt hawg tires..... used a stop watch and 60ft avg the times and wow 45mph for about the first 2-5 mins. (these were full speed passes not from a stand still)
  13. Thread: wheelies

    by earthmover
    Replies
    15
    Views
    442

    forgot to add...... put in some trinity blue...

    forgot to add...... put in some trinity blue springs in the rear and lean you low until the engine quits after 2sec of squezzing the fuel line.... you can keep the high richer since it does not...
  14. Thread: wheelies

    by earthmover
    Replies
    15
    Views
    442

    my max is geared at 16x72 with the xtm engine...

    my max is geared at 16x72 with the xtm engine wheelies no problem ...geared at 18x72 not happening unless in grass.
  15. I get 10-15 mins on cheap radio shack 2000...

    I get 10-15 mins on cheap radio shack 2000 (almost a year on those batts) using a superbrain . geared at 15x87 speed 45mph wheelies at every start. geared at 18x87 no wheelies but speed 48-50 ......
  16. Replies
    13
    Views
    453

    My problem was that the antenna seperated from...

    My problem was that the antenna seperated from the receiver...I just soldered another 30g wire to the receiver (little longer too)works great. I will never run without a failsafe again.

    Nothing...
  17. Replies
    13
    Views
    453

    XTM has a failsafe selling for $20 at...

    XTM has a failsafe selling for $20 at hobbypeople.net
  18. Replies
    2
    Views
    196

    ESC Performance???

    I searched the forum and some of what I was looking for was vague so heres my question.....

    I run the stock esc with a 16t double in my rustler. Still going to this day. The esc runs long...
  19. Replies
    14
    Views
    313

    The Statment below came from Misbehavin website ...

    The Statment below came from Misbehavin website

    "The MRC Super Brain has built a reputation as a good inexpensive charger. However some of the earlier ones that shipped seem to start false peaking...
  20. Replies
    6
    Views
    227

    Thanks for the clarification. I did not know...

    Thanks for the clarification. I did not know the carriers needed to be upgraded as well. Since its my sons truck age 7 I think I will stick to stock size until it breaks...

    So stock bearings...
  21. Replies
    14
    Views
    313

    Thanks for all the responses! Fot those that...

    Thanks for all the responses! Fot those that own the Black Widow Pro.... What are average charge times? Does it have a cooling fan? How about the same ??'s for the super brain
    Most of my batts...
  22. Replies
    14
    Views
    313

    Does anyone in the forum use these chargers? I...

    Does anyone in the forum use these chargers? I dont want to make a bad investment........
  23. Replies
    6
    Views
    227

    Bearing Confusion

    What size bearings do you use for the wheels?
    Is it 5x8x2.5 or 5x11x4?

    The bushings are 5x8x2.5 but I read to put in 5x11x4. Please clear the confusion.
  24. Replies
    14
    Views
    313

    Help in choosing

    I am currently using a Hobbico 900 charger that I modified with a 60minute timer (great charger 10yrs old) but I am sure I'm missing the peaks. I am looking at the Black Widow Pro and the ...
  25. Replies
    14
    Views
    334

    i bought the trinity 16t double also..........

    i bought the trinity 16t double also....... running 15 / 84 gear ratio... running fast and long with stock x1-esc..... anyone know what turn the x1 can handle???
Results 1 to 25 of 78
Page 1 of 4 1 2 3 4