Search:

Type: Posts; User: brushlessbrah

Page 1 of 2 1 2

Search: Search took 0.29 seconds.

  1. I' call it bullet proof for the most part. I was...

    I' call it bullet proof for the most part. I was grenadeing the shaft ends of the stock shaft.
  2. Replies
    7
    Views
    188

    Should be g2g with an mmp but honestly I don't...

    Should be g2g with an mmp but honestly I don't know too much so hopefully someone answers that with confidence, mines hooked up to a monster.
  3. At 18/54 on a 3s my 2650 has/does separate the...

    At 18/54 on a 3s my 2650 has/does separate the split six bead locks, only little pieces of the tire will pop free and cause a little wobble. Like said above, I assemble mine then lightly glue around...
  4. Replies
    33
    Views
    416

    I only use red for my entire truck, it's how it...

    I only use red for my entire truck, it's how it is applied that makes all the difference.
  5. Replies
    13
    Views
    274

    If you look at the end of the set screw they are...

    If you look at the end of the set screw they are slightly beveled to press down on the hole of the diff shaft. If they are not perfectly centered above the hole the set screw will not tighten flush,...
  6. Replies
    13
    Views
    274

    Judging From your picture and my past experience...

    Judging From your picture and my past experience you don't have the set screws perfectly aligned on the diff shafts, causing your set screws to petrude further than normal. I have used permant...
  7. Replies
    11
    Views
    228

    I use permanent thread locker on all my threads....

    I use permanent thread locker on all my threads. I've had screws fall out that I had temporary locked. My method of madness is to fasten the screw about 95% then apply a smudge of permanent using a...
  8. http://i611.photobucket.com/albums/tt197/brettcurt...

    http://i611.photobucket.com/albums/tt197/brettcurtisherpich/image_zps1056e386.jpg

    It's strong. I cut a square of aluminum and 3M'ed it. I can lift up my entire truck by the esc.
  9. Replies
    4
    Views
    190

    May sound lame but inspect the inside of your...

    May sound lame but inspect the inside of your horn maybe a striped tooth?
  10. Replies
    17
    Views
    293

    Nice look.

    Nice look.
  11. I've never had a batt tossed on me using the...

    I've never had a batt tossed on me using the traxxas ext kit. And I bash hard. No I don't personally use Velcro but my friend does, on a custom alum chassis. Does your mount look like mine?
    ...
  12. Replies
    5
    Views
    102

    Then off to the hobby shop to buy some steel axles

    Then off to the hobby shop to buy some steel axles
  13. Replies
    3
    Views
    162

    Introducing My 4x4 build

    I bought an ultimate 4x4 about two years ago. Ran it for a year ish then packed it up. Recently got back into it so I thought I'd post some dirty pics of my one off slash.

    MMP2 / 2650(1/8)
    MIP X...
  14. Replies
    17
    Views
    268

    MIP X DUTY. Go big or go home.

    MIP X DUTY. Go big or go home.
  15. Build up an E Revo slipper, you'll love it, I...

    Build up an E Revo slipper, you'll love it, I guarantee it.
  16. Replies
    7
    Views
    177

    I burn through trenchers. 2.2/3.0. I also bash...

    I burn through trenchers. 2.2/3.0. I also bash pretty hard, then throw down some speed runs, and the normal race around the streets so I don't expect NOT to burn any tire I run like that. I have had...
  17. Replies
    9
    Views
    226

    I run X Ds. It's not the axles causing your...

    I run X Ds. It's not the axles causing your problem, it's your bearings causing your bearing problem. You can service rubber sealed bearings but IMO you will save a lot of wrench time if you upgrade...
  18. Replies
    46
    Views
    1,179

    I'd. Bash with you

    I'd. Bash with you
  19. Looks nice

    Looks nice
  20. If getting so hot your considering cutting a...

    If getting so hot your considering cutting a hole in your chassis? Seems like a heat sink and fan upgrade would be a better option. If gearing and fans can't keep you cool I think you have bigger...
  21. Replies
    10
    Views
    169

    Take it part and check the power connection, it's...

    Take it part and check the power connection, it's inside the grip near your palm.
  22. Replies
    10
    Views
    169

    I have ran my tqi for a year and then last week I...

    I have ran my tqi for a year and then last week I started getting servo spasms. Troubleshot for hours then went out and bought a specktrum transmitter/reciever. Problem solved. Traxxas said send them...
  23. Replies
    31
    Views
    506

    I blew through my stock tires pretty quick, went...

    I blew through my stock tires pretty quick, went proline, have ran almost every tire they make and I'm sticking with them.
  24. Replies
    11
    Views
    286

    IMO : Locktite is important but be certain the...

    IMO : Locktite is important but be certain the set screws are PERFECTLY fastened on the diff, I have rushed a repair more than once and went liberal on the locktite and still spun them apart, but...
  25. One day a bunch of kids were outside with a...

    One day a bunch of kids were outside with a target brand rc truck so of course I had to whip out my 4x4. Ended up using their kicker ramp to jump over their dads silverado about five times, landing...
Results 1 to 25 of 39
Page 1 of 2 1 2