Search:

Type: Posts; User: Just go Play

Page 1 of 20 1 2 3 4

Search: Search took 0.14 seconds.

  1. I've run the following motors in my slash using...

    I've run the following motors in my slash using an MM esc.

    vxl: great 2s motor, fast on 3s but ran a little hot in the summer.

    HV6.5: my favorite all round motor running 2s-4s this motor never...
  2. Replies
    70
    Views
    2,465

    ...

    <<<<<--Cut to the Important stuff-->>>>>



    This is the voltage that components start popping at. Traxxas has been pretty spot on in the past so this is likely the very outside limit of the...
  3. Replies
    3
    Views
    240

    I included tires because some combinations can be...

    I included tires because some combinations can be tall/short/heavy enough that they make a noticeable difference when choosing gearing. Axial 40 series beadlock wheels with a large tire like say...
  4. Replies
    3
    Views
    240

    Gearing is going to depend on your battery...

    Gearing is going to depend on your battery voltage 4/5/6s, tire size, and how fast you want to go. As a reference I tend to run 16/36 on 5s with std 2nd gear ratio and 5.8" tires which gets me around...
  5. Replies
    43
    Views
    1,773

    Is it just me or does someone have some...

    Is it just me or does someone have some unaddressed issues that should be discussed with their therapist? Why do you care how much money anyone chooses to spend on their toys or how they choose to...
  6. Replies
    65
    Views
    1,936

    I never said anything about it not being safe to...

    I never said anything about it not being safe to charge them at 2c rates. I said that charging them at 2c rates would shorted their life, as in the number of charges until they experience noticeable...
  7. This is not a servo or electrical problem. All...

    This is not a servo or electrical problem. All you need to do is correctly set your wheel alignment paying extra attention to the rear wheels.

    If you find it difficult to get the rear toe set...
  8. Replies
    48
    Views
    1,456

    I've run a vxl motor and hv6.5 (3500/3100kv) on...

    I've run a vxl motor and hv6.5 (3500/3100kv) on 4cells with 54/21 gearing (vxl motor really did not like that) and neither setup is as fast as my vxl rustler on 3cells. Thats not to say it was not...
  9. This is how I fixed the nuts on my ofna hubs....

    This is how I fixed the nuts on my ofna hubs.
    http://i177.photobucket.com/albums/w202/mistercrash1964/No%20slop%20Ofna%20adapters/Other%20mods%20to%20the%20adapters/adapters_nut1.jpg
    This should...
  10. Replies
    65
    Views
    1,936

    The eternal MA debates live on so heres another...

    The eternal MA debates live on so heres another worthless 2 cents for your consideration...

    Nobody reputable has tested the new MA packs to rate them for actual results.. (I do not believe that...
  11. Replies
    10
    Views
    346

    I don't know about the newer ones but I have used...

    I don't know about the newer ones but I have used the older ones to clock a friend pitching hardballs. I should point out that your local authorities may not show the same appreciation of their...
  12. Replies
    23
    Views
    441

    With all the threads about SPC packs blowing up...

    With all the threads about SPC packs blowing up or just plain sucking I can see why you find that so hard to believe...:rolleyes:
  13. Replies
    35
    Views
    667

    Very impressive numbers snellemin! I don't...

    Very impressive numbers snellemin!

    I don't suppose you have a NiMH pack sitting around that you could run in that setup purely for comparison of voltage drop under that kind of load?

    BTW is...
  14. Technically that is correct but is not applicable...

    Technically that is correct but is not applicable to the conditions that RC's or most any land vehicle will be operated under.

    Gears break when their resistance to rotating is highest which is...
  15. He may not be the only one but make no mistake,...

    He may not be the only one but make no mistake, he is a certified professional! His dedication to destruction is truly amazing.
  16. Replies
    18
    Views
    665

    LOL I'm making that my new signature! :D

    LOL I'm making that my new signature! :D
  17. Replies
    9
    Views
    447

    You can but it's really only good for drag...

    You can but it's really only good for drag racing. Otherwise they over heat really fast and tend not to live very long.
  18. Replies
    9
    Views
    447

    FWIW: I ran a 7700 off a VXL-3s for a while in a...

    FWIW: I ran a 7700 off a VXL-3s for a while in a 1/10 TC and the controller ended up dying after about 3 months of use. It is entirely possible that this was purely coincidence or maybe it just did...
  19. Replies
    3
    Views
    275

    JC: just wondering if you had a specific reason...

    JC: just wondering if you had a specific reason for needing a hard case pack (like possibly local track rules or w/e) or id it just for the safety aspect? If it's the later then Briang's suggestion...
  20. Replies
    6
    Views
    468

    runtime is going to depend on the amount of...

    runtime is going to depend on the amount of energy being used by the motor. There are a whole lot of variables that will effect this but in general I think the runtimes are going to be reasonably...
  21. Lets face it, electronics and H2O do not tend to...

    Lets face it, electronics and H2O do not tend to play nice together and can even be dangerous. If you use some common sense (does that exist anymore) you should be able to use your mamba max in the...
  22. Replies
    14
    Views
    884

    I'm not sure if you want to shift more weight...

    I'm not sure if you want to shift more weight forward... having the truck that low and having very little suspension does not allow for the weight to transfer to the rear under acceleration. On the...
  23. Replies
    16
    Views
    1,036

    You can find a basic explanation here...

    You can find a basic explanation here and google should get you many sites with more detailed info depending what your looking for.
  24. Replies
    16
    Views
    1,036

    Thats not correct... The gears are measured in...

    Thats not correct... The gears are measured in diametral pitch which means that a 48 pitch gear with 48t would have a diameter of 1". To calculate the distance between the teeth you would figure the...
  25. Replies
    27
    Views
    1,255

    The 58t spur can be a tight fit and may even rub...

    The 58t spur can be a tight fit and may even rub the drive shafts. The 56 and 54t both fit no problem. E/Tmaxx pinions will work fine with the jato spurs, I don't think I've ever seen a .8m pinion in...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4