Search:

Type: Posts; User: ntmaxx

Page 1 of 7 1 2 3 4

Search: Search took 0.24 seconds.

  1. Thread: air filter

    by ntmaxx
    Replies
    7
    Views
    363

    Something like THIS....

    Something like THIS.
  2. Replies
    5
    Views
    344

    Make shure your controller is set to 50/50, and...

    Make shure your controller is set to 50/50, and not 70/30. 70/30 would give you too many degrees of rotation at the servo, which would move your throttle too far.
  3. Replies
    3
    Views
    221

    Put a dab of silicone on the clips. I use a tooth...

    Put a dab of silicone on the clips. I use a tooth pick and put it over the end of the pin and clip. Haven't lost one yet.
  4. Replies
    11
    Views
    416

    9.33333333..... it never ends. The bell boy...

    9.33333333..... it never ends. The bell boy should have given them each 1.666.... to be exact.

    Which came first, chicken or egg?
  5. Replies
    11
    Views
    416

    Each man paid 9.333...,which = 28, plus the 2 the...

    Each man paid 9.333...,which = 28, plus the 2 the bellboy kept makes 30.
  6. Thread: Wow! O.S.

    by ntmaxx
    Replies
    3
    Views
    326

    Wow! O.S.

    I know O.S. makes a nice engine, but, is it really worth the amount T.H. is asking for the new .21 tm? Click here That is a little steep don't you think?
  7. Replies
    25
    Views
    622

    http://www.2coolrc.com/detail.aspx?ID=488

    http://www.2coolrc.com/detail.aspx?ID=488
  8. T.H. has them in stock....

    T.H. has them in stock.
  9. http://www.buytraxxas.com/product_info.php?cPath=4...

    http://www.buytraxxas.com/product_info.php?cPath=4_718&products_id=1001

    Is this what your talking about?
  10. Thread: 70/30???

    by ntmaxx
    Replies
    16
    Views
    384

    With 70-30 you are better able to modulate the...

    With 70-30 you are better able to modulate the throttle.
  11. Replies
    18
    Views
    576

    I run O rings in place of the plastic ties. They...

    I run O rings in place of the plastic ties. They are sized a little smaller than the rubber boot for the filter. When it is put on it stays on. Works realy good.
  12. Replies
    4
    Views
    232

    Flip your diffs. You are using reverse gear for...

    Flip your diffs. You are using reverse gear for forward running. Take the front diff and turn it 180 deg. and then do the same for the rear. The small metal gear is not used for forward operation. It...
  13. Replies
    6
    Views
    241

    cliky...

    cliky

    Scroll to the bottom of the link. You will find the 4 wheel drive and reverse upgrades.
  14. Replies
    9
    Views
    352

    Put some shims behind the split bevel cone. That...

    Put some shims behind the split bevel cone. That will move the flywheel away from the carb.
  15. Thread: pinch test???

    by ntmaxx
    Replies
    8
    Views
    333

    The following is from the tunning sticky. No# 3...

    The following is from the tunning sticky. No# 3 seems to suggest your lsn is too rich.

    "Pinch test for setting your LSN

    1. With the motor warmed up do a WOT pass then pinch the fuel line 1-2...
  16. Replies
    12
    Views
    471

    Usually they are an A.B.C. construction....

    Usually they are an A.B.C. construction. Aluminum-piston, Brass cylinder with a chrome finish on the cylinder for wear.
  17. Replies
    16
    Views
    433

    Check your clutch bell bearings. Looking at the...

    Check your clutch bell bearings. Looking at the wear pattern on the spur it looks like the one furthest from the engine on the pilot shaft is shot.
  18. Replies
    13
    Views
    355

    So sorry, I messed up....

    So sorry, I messed up. http://www.misbehavin-rc.com/pit-lane/receiver-repair/g-receiver-repair.asp

    That one gives length and a the procedure for reparing.
  19. Replies
    13
    Views
    355

    http://www.misbehavin-rc.com/pit-lane/antenna/g-an...

    http://www.misbehavin-rc.com/pit-lane/antenna/g-antenna.asp
  20. Replies
    4
    Views
    171

    Link to the instructions....

    Link to the instructions.

    Well that don't work.

    Go to the bottom and look for "how to". It's in there.

    http://www.prolineracing.com/howtotips/maxx-steering.html

    I think this works now.
  21. Replies
    9
    Views
    253

    "If it was the slipper being too loose the pegs...

    "If it was the slipper being too loose the pegs would get fried. SO inspect the peg area for anything that looks melted."


    If he had the old black trany that would be true. But I do believe, from...
  22. Replies
    9
    Views
    253

    What you describe sounds like a slipper that is...

    What you describe sounds like a slipper that is on the loose side. Tighten it up a little and try again.
  23. Replies
    15
    Views
    466

    I think the shock tower mount looks to be the...

    I think the shock tower mount looks to be the weakest area on the bulks.
  24. Replies
    12
    Views
    327

    I just got to know where you got the mini jack? ...

    I just got to know where you got the mini jack?

    Oh yea- the truck looks sweet so far.
  25. Replies
    42
    Views
    796

    Your friend needs as much help as his Maxx.:(

    Your friend needs as much help as his Maxx.:(
Results 1 to 25 of 153
Page 1 of 7 1 2 3 4