Search:

Type: Posts; User: JackSlash

Page 1 of 6 1 2 3 4

Search: Search took 0.11 seconds.

  1. Replies
    6
    Views
    267

    on youtube search " mip stampede review" in the...

    on youtube search " mip stampede review" in the top video listed it shows where some "normal" rubbing occurs. hope that helps
  2. Replies
    6
    Views
    267

    Those carriers should be switchable, from side to...

    Those carriers should be switchable, from side to side. doing so should will change the toe-in. maybe its too much of an angle for the shafts. btw......where is the rubbing?
  3. Replies
    2
    Views
    90

    Mod .8 or 32p (both same thing) pinions with a...

    Mod .8 or 32p (both same thing) pinions with a 1/8'' or 3mm shaft bore size match up with traxxas spur gears. what sizes are you going to run?
  4. Replies
    6
    Views
    221

    I bash mine on 3s with a tacon 2150 and they...

    I bash mine on 3s with a tacon 2150 and they handle the power great. Like Shaky said, great design thats tried and true. I did break a steering knuckle.... but it was a high speed asphalt quadruple...
  5. Replies
    14
    Views
    549

    If you like to test things out, i always like to...

    If you like to test things out, i always like to set it maxed, give it a run, set it minimum.... give it another run, then you'l have a better idea of what 50%.... 30% etc will actually be doing..
    ...
  6. Replies
    14
    Views
    549

    Punch control can be a big help for protecting...

    Punch control can be a big help for protecting the driveline. It reduces the "all at once" power to the wheels, and just gradually applies the throttle depending on how much punch you set..

    Both...
  7. Replies
    14
    Views
    549

    sorry to hear about the bad luck. Is this your...

    sorry to hear about the bad luck. Is this your 1st r/c with real electric power? anything that size on 6s can get tore upp pretty quick. like shogun said, good throttle/ brake control helps, and...
  8. Replies
    14
    Views
    516

    Set up the video camera, charge it up... then go...

    Set up the video camera, charge it up... then go for 6 cartwheels lol
  9. Thread: Help!!!!

    by JackSlash
    Replies
    15
    Views
    231

    Have you tried any adjusting of the slipper?...

    Have you tried any adjusting of the slipper? maybe ighten it a bit to compensate for wear
  10. Replies
    16
    Views
    388

    yes, thats it...... and my sons platinum came...

    yes, thats it...... and my sons platinum came with the plastic one
  11. Replies
    3
    Views
    410

    what adapters are you using?

    what adapters are you using?
  12. Replies
    9
    Views
    662

    These look similar in size to 2.8 trenchers on a...

    These look similar in size to 2.8 trenchers on a slash... from your pic anyway.... close?
  13. Replies
    16
    Views
    388

    Something has got to be wrong.. you said the spur...

    Something has got to be wrong.. you said the spur moves 1-2mm? do you still run the plastic bearing adapter on the slipper? have you checked it? the motor mount and bearing? both common problem...
  14. Replies
    6
    Views
    304

    An old auto shop trick was to put it in the...

    An old auto shop trick was to put it in the freezer for 20mins... when you take it out the outer aluminum housing should heat up just a bit quicker from hand warmth then the inner steel bearing.......
  15. yes, 3s will heat it up quick... and as far as...

    yes, 3s will heat it up quick... and as far as the driveline holding up, its all about how its driven, and also a biggie is how tight the slipper clutch is set.
    and...... if you go faster..........
  16. Replies
    58
    Views
    3,794

    Thanks! and sorry about your new breakage, are...

    Thanks! and sorry about your new breakage, are you just gonna replace it and give it another go?
  17. Replies
    13
    Views
    310

    Not really here.... especially if you keep the...

    Not really here.... especially if you keep the sliding/telescoping action clean
  18. Replies
    58
    Views
    3,794

    Great Job! thanks for sharing... with quality...

    Great Job! thanks for sharing... with quality pics too, your spoiling us lol...

    so following along your thread it looks like xo 1 front steering hubs are a direct fit with tekno's? i also run thr...
  19. Thread: Rear A Arms

    by JackSlash
    Replies
    5
    Views
    599

    Here's a link to he exploded views page for the...

    Here's a link to he exploded views page for the nitro slash. See if you can find it there.... http://traxxas.com/products/models/nitro/44054nitroslash-downloads
    Welcome to the hobby! You'll learn...
  20. your links not working for me

    your links not working for me
  21. Replies
    6
    Views
    612

    You can try and reverse the servo's on the tx.......

    You can try and reverse the servo's on the tx.... sounds like its not getting the signals it needs
  22. Replies
    5
    Views
    219

    You'll be happy with a platinum for sure then!

    You'll be happy with a platinum for sure then!
  23. Replies
    5
    Views
    219

    Yes, a platinum is exactly that.... what are your...

    Yes, a platinum is exactly that.... what are your plans for the truck? stock vxl?
  24. I would take the motor out first, then give it a...

    I would take the motor out first, then give it a roll back and forth. Doing this will eliminate any noise from the motor, and you'll hear the diff gears much better.
    Also, have you checked to see...
  25. Replies
    14
    Views
    524

    another thought is to check the grub screw on the...

    another thought is to check the grub screw on the slipper output shaft. make sure it didn't loosen up and rotate off of the flat area. that could spin and squeal in a load situation...?
Results 1 to 25 of 131
Page 1 of 6 1 2 3 4