Search:

Type: Posts; User: 65535

Page 1 of 16 1 2 3 4

Search: Search took 0.12 seconds.

  1. Replies
    2
    Views
    805

    Try swapping the servo, they can cause all sorts...

    Try swapping the servo, they can cause all sorts of issues when they go out.
  2. Replies
    16
    Views
    1,249

    The only issue I have with the stock (and RPM...

    The only issue I have with the stock (and RPM True trak) carriers is getting worn out from dirt ingress. Despite the boots and plugs they get grit in them and destroy the smooth plastic bearing...
  3. Replies
    31
    Views
    1,714

    Take an aluminum soda can and cut a thin strip...

    Take an aluminum soda can and cut a thin strip about 3mm wide and just a bit shorter than the circumference of the coupler, bend it around the coupler over the pin. Tape it in place then cover with...
  4. Thread: will they fit?

    by 65535
    Replies
    5
    Views
    867

    They may rub on the carriers, monster truck tires...

    They may rub on the carriers, monster truck tires and buggy tires are very different in size.
  5. Thread: Aluminum

    by 65535
    Replies
    12
    Views
    1,079

    HPP hubs and motor brace are excellent aluminum...

    HPP hubs and motor brace are excellent aluminum to have on your truck.
  6. Replies
    231
    Views
    20,097

    the Type of 3D printing he used is an extrusion...

    the Type of 3D printing he used is an extrusion process.

    A common and relatively inexpensive way of 3D printing in plastic is to use a plastic monofilament (ABS and PLA are very common) fed into a...
  7. Replies
    14
    Views
    1,324

    I had the two front diff bearings on the input...

    I had the two front diff bearings on the input shaft go out and it had those exact symptoms. The bearings shredded and balls where imbedded in the case and in gear teeth.
  8. The design of the diffs isn't completely awful....

    The design of the diffs isn't completely awful. But the materials are, the cases should be made out of a FRP rather than what they are made out of which I believe is plain nylon or something similar....
  9. Replies
    29
    Views
    1,331

    I just cut the stock plastic servo saver arm off...

    I just cut the stock plastic servo saver arm off and put in a single servo, mine had the same spline mount as stock so I used the stock servo arm. No issues cost me $130 flat. I'm at .09s/60 419Oz*In.
  10. Replies
    22
    Views
    1,101

    I think he was talking about the plastic chassis,...

    I think he was talking about the plastic chassis, which has a lot of molded support in the central tube and the structure of the battery boxes and vertical components to give it much higher strength....
  11. Replies
    25
    Views
    924

    I do the same, I use backlash to adjust mesh.

    I do the same, I use backlash to adjust mesh.
  12. Thread: Velcro

    by 65535
    Replies
    16
    Views
    954

    I only used velcro on the battery compartment...

    I only used velcro on the battery compartment doors but after trashing my stock body I decided to use both velcro and body clips.
  13. Thread: 54t spur fit?

    by 65535
    Replies
    36
    Views
    2,129

    That's not touching? I never had an issue myself...

    That's not touching? I never had an issue myself when using proper gear ratios. The platform was originally designed for a much small motor and ESC.

    That would be a design issue not a quality...
  14. Replies
    6
    Views
    1,333

    Well let's put it this way the 2200Kv Mamba...

    Well let's put it this way the 2200Kv Mamba Monster setup will have slightly less torque than a comparable 2000Kv motor, the Mamba Monster already has enough torque to shred the driveline if not and...
  15. Replies
    7
    Views
    599

    The stops are in there for a reason, depending on...

    The stops are in there for a reason, depending on which driveshafts you use there is a maximum drive angle on the joints. Plus as mentioned before the stop is part of the support structure for the...
  16. Brown is the negative side so you want it to be...

    Brown is the negative side so you want it to be on the same side as the black wire. The ESC will beep when it arms and does a cell count.

    It appears your picture is backwards.
  17. Replies
    9
    Views
    500

    Most of the time it's the pivot ball cap screws...

    Most of the time it's the pivot ball cap screws that are too tight. I've noticed stock pivot balls are rarely totally round and can bind. You want to loosen the cap screw until it doesn't bind at the...
  18. Replies
    5
    Views
    495

    Your motor will only get hotter when the air...

    Your motor will only get hotter when the air warms up. You should re-gear.

    The magnets in modern high performance electric motors have magnets that are much stronger but are also much more...
  19. Replies
    22
    Views
    883

    Sounds like your gear mesh is horribly tight too.

    Sounds like your gear mesh is horribly tight too.
  20. Replies
    19
    Views
    691

    That's what I run behaves very well.

    That's what I run behaves very well.
  21. Thread: 6s problems

    by 65535
    Replies
    15
    Views
    608

    Backflips and wheelies are amusing on video...

    Backflips and wheelies are amusing on video occasionally but it puts a lot of strain on your truck and it's a good way to break things.
  22. Replies
    18
    Views
    629

    Not that I would recommend it I had issues with...

    Not that I would recommend it I had issues with my switch so when I had the case open to solder in the leads for voltage sensing and the castle BEC (I soldered them onto the same pads as the input...
  23. Replies
    15
    Views
    959

    Well it it's not anything around the motor I...

    Well it it's not anything around the motor I would start checking bearings. They tend to squeak to death. Worst thing is if a bearing fails completely it can take other parts with it.
  24. Replies
    15
    Views
    959

    If it's not the slipper then over tightened gear...

    If it's not the slipper then over tightened gear mesh is the next common issue.
  25. Replies
    13
    Views
    827

    I run my Badlands and Paddles on Desperados in a...

    I run my Badlands and Paddles on Desperados in a black (not chromed) and they work very well.

    Badlands are great, truggy tires are good but are more prone to wearing out. Definitely want to match...
Results 1 to 25 of 391
Page 1 of 16 1 2 3 4