Search:

Type: Posts; User: Hardcoretam

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    15
    Views
    321

    Where does it say he never followed the break in?

    Where does it say he never followed the break in?
  2. Replies
    14
    Views
    286

    Maybe the motor is so worn it will only spin when...

    Maybe the motor is so worn it will only spin when it's not connected to the rest of the gearbox
  3. Replies
    26
    Views
    789

    That's probably why the brush wire came off, the...

    That's probably why the brush wire came off, the motor will have overheated. Chances are you've lost a bit of performance now i'm afraid so even when it's geared right it might not be so fast...
  4. Oops my bad. I doctored my response to another...

    Oops my bad. I doctored my response to another thread about breaking in brushed motors.
    ignore the gearing part completely
  5. If i had a Titan motor i'd start by breaking the...

    If i had a Titan motor i'd start by breaking the motor in underwater for 30minutes on 2 x aa batterys (3volts)
    I'd take out the motor and dry it off fully and lube the bushings with oil.
    I'd then...
  6. Replies
    19
    Views
    774

    That's not the best way of breaking in a titan...

    That's not the best way of breaking in a titan motor IMO.

    If i had a Titan motor i'd start by breaking the motor in underwater for 10 minuts on 2 x aa batterys (3volts)
    I'd take out the motor and...
  7. Replies
    6
    Views
    330

    Titans are overgeared out the factory for bashing...

    Titans are overgeared out the factory for bashing imo. This is why they fail so fast. with a 13tooth pinion the 15t motor might not be faster top end than the titan. probably the same, but it will be...
  8. Replies
    26
    Views
    789

    I was just about to say the same thing. If that...

    I was just about to say the same thing.
    If that wire came off of the 15t motor it probably has overheated at least once.
    What gearing are you using on it?
  9. Replies
    24
    Views
    537

    I agree with a lot of people that a 6amp charge...

    I agree with a lot of people that a 6amp charge isn't overly harsh for top end packs, but wouldn't you agree it's pretty aggressive charge for it's first charge. I sooth in all my batterys then...
  10. Replies
    17
    Views
    1,142

    Yes, someone told you a few posts up

    Yes, someone told you a few posts up
  11. Replies
    32
    Views
    499

    The stock drivelines of cars back then were much...

    The stock drivelines of cars back then were much worse, with some having no slipper clutch

    A 9t brushed motor was stupid fast for brushed back in the day. On a good 6 cell it would probably have...
  12. Replies
    24
    Views
    537

    A brand new battery does better if it's broken...

    A brand new battery does better if it's broken in.
    I charge at 0.2amps for the first thing and slowly progress. I don't charge at the maximum charge rate untill it's be charged about 10 times
  13. Replies
    27
    Views
    1,083

    Not overly. When the motor fails the bearing will...

    Not overly. When the motor fails the bearing will still be fine, so it can be used for all future motors
  14. Did you really have to make 3 seperate threads...

    Did you really have to make 3 seperate threads about the same thing?
  15. People run non waterproof lipos and NiMH packs...

    People run non waterproof lipos and NiMH packs under water all the time (me included) with no issues. It's a bit of a gimmic as water doesn't really do much to them as long as it's not salty
  16. Replies
    19
    Views
    2,093

    They may have more RPM when unloaded, but under...

    They may have more RPM when unloaded, but under load they won't be able to achieve thier max RPM as easily as the HO's
    The HO's are superior on all performance levels
  17. Replies
    27
    Views
    1,083

    Either do a search on here, or read the owners...

    Either do a search on here, or read the owners manual
  18. Replies
    5
    Views
    836

    I doubt the esc would handle that motor well,...

    I doubt the esc would handle that motor well, even just on 3s
  19. Ideally with many brushed motors 140oF is about...

    Ideally with many brushed motors 140oF is about the high end of the tempretures i like to run constantly. I like 130oF constantly.
    A lot of brushed motors start to become damaged after 160oF
  20. The 8.5t 4000kv is the one i would use if i was...

    The 8.5t 4000kv is the one i would use if i was using 2s lipo or 7 cell packs. I would watch the tempretures on the motor though. I've not enough insight to say how good the motors are. I've not ran...
  21. I would run the 60amp speed control in an all...

    I would run the 60amp speed control in an all alloy rustler and choose something with 4000kv or less for bashing with. I wouldn't think it was too much truck for the speed control.
    It's not really...
  22. The set up was a 17.5turn 50mm (540) motor...

    The set up was a 17.5turn 50mm (540) motor unsensored and 2400kv
    It was a 2 pole motor.
    It had an 80mm cooling fan over it and a clip on heat sink with thermal paste.
    2 x 2s lipo in series and the...
  23. All he was doing was running a UBEC though. The...

    All he was doing was running a UBEC though. The speed control comes standard with caps. The tempretures he was seeing running that set up are very impressive imo. Over voltaged and heavy loads from...
  24. Replies
    14
    Views
    712

    You can go crazy on 4s with the Mamba Max as...

    You can go crazy on 4s with the Mamba Max as well, with a little UBEC
  25. Theres a member of the E-Savage forums who...

    Theres a member of the E-Savage forums who happens to be a bit of a Guru on RC electronics. When he read up about the caps on the 60amp EZ run he pointed out they were not designed for 14.8volts. In...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4