Search:

Type: Posts; User: 67camaro

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    4
    Views
    230

    I'll open it up and check out the gears today.

    I'll open it up and check out the gears today.
  2. Replies
    4
    Views
    230

    Got a used one I'll sell for $8 shipped if you're...

    Got a used one I'll sell for $8 shipped if you're in US
  3. I've got a Revo with a RB TM523 and Trinity...

    I've got a Revo with a RB TM523 and Trinity exhaust and a lot more upgrades for $300 +shipping. If interested send me a pm with your email and I'll send you some pics.
  4. Replies
    2
    Views
    232

    pm sent!!!

    pm sent!!!
  5. Replies
    31
    Views
    1,020

    You will have to open out the front slot on the...

    You will have to open out the front slot on the 4910 chassis where the drive shaft passes through and cut some length off the front drive shaft. I see you bought the 4907 trans w/slipper, make sure...
  6. Replies
    12
    Views
    460

    the standard a-arms on the old pro .15 are...

    the standard a-arms on the old pro .15 are considered wide stance? no

    Can I get just as wide with this old chassis just by changing out the a-arms, axle shafts and carriers then? yes the tmaxx 2.5...
  7. Replies
    12
    Views
    460

    Buy a new 3.3 from EBay for about $110 shipped...

    Buy a new 3.3 from EBay for about $110 shipped then sell the old carb for $15-20 and $10 for the rest of the engine.
    I prefer plastic over aluminum parts for the price cause you'll still end up...
  8. Replies
    12
    Views
    460

    you will be able to use your rear center shaft...

    you will be able to use your rear center shaft but for the front you will need #4951x half shafts cut down so that the straight section of each half shaft is 1.75" long, do not include the U end of...
  9. Replies
    12
    Views
    460

    Yes the front and rear end parts will switch...

    Yes the front and rear end parts will switch over. But you will need the longer chassis braces and the new style throttle linkage. Also you will need to make new center drive shafts out of axles...
  10. Replies
    4
    Views
    165

    To clean I remove the wheels, electronics and...

    To clean I remove the wheels, electronics and wrap the slots in the starter motor with electrical tape then take it, along with wheels to coin wash. Use compressor to blow dry at home then spray...
  11. Replies
    1
    Views
    121

    Make sure you run a full tank of fuel through it...

    Make sure you run a full tank of fuel through it without it stalling. Go through and tighten as many screws as you can to check for some that might be stripped.
  12. Thread: clutchbell

    by 67camaro
    Replies
    5
    Views
    189

    Check for Teflon washer or you might have to use...

    Check for Teflon washer or you might have to use another washer between block bearing and the cone.
  13. Replies
    12
    Views
    711

    Really helps protect the rear part of body from...

    Really helps protect the rear part of body from cracking.
  14. Thread: wtb: 4x4

    by 67camaro
    Replies
    3
    Views
    292

    I have a used extended 3.3 T-Maxx with a brand...

    I have a used extended 3.3 T-Maxx with a brand new never started 3.3 engine in excellent condition for $260 + actual shipping. Send me a pm with email address so I can send some pics if interested.
  15. Replies
    8
    Views
    259

    http://www.rcnitrotalk.com/misc/tuning-flowchart.p...

    http://www.rcnitrotalk.com/misc/tuning-flowchart.pdf

    I printed this flowchart and had it laminated at Staples. I don't leave home without it.
  16. Replies
    1
    Views
    372

    Spotted these on ebay...

    Spotted these on ebay
    http://www.ebay.com/itm/Traxxas-TMaxx-Yellow-Nylon-Reinforced-Posts-/330828392001?pt=US_Character_Radio_Control_Toys&hash=item4d06e8a641
  17. Replies
    15
    Views
    1,455

    6volt with 5 2/3a cells either flat or hump pack...

    6volt with 5 2/3a cells either flat or hump pack will fit, just make sure it has the right connector on it. Wouldn't purchase under 1600mah.
  18. Replies
    7
    Views
    505

    Never had a problem with the blue even on plastic.

    Never had a problem with the blue even on plastic.
  19. Replies
    15
    Views
    1,455

    Some of the newer Revos and slayers use a 5324x...

    Some of the newer Revos and slayers use a 5324x rx/battery box that is universal in the fact that you can use a flat pack or a hump pack. The first of this style came on the revo platinum as a 5324r...
  20. Replies
    7
    Views
    505

    When you put it back together use a drop of blue...

    When you put it back together use a drop of blue loc tight on the threads of the screw pin.
  21. I believe the 4909 tmaxx was the only model that...

    I believe the 4909 tmaxx was the only model that came with opti drive. When they come up for sale they usually fetch a good price. Earlier this year I sold a new one for $110. Used ones go for $60...
  22. Replies
    13
    Views
    1,443

    I use Mothers Mag and Aluminum Polish on my...

    I use Mothers Mag and Aluminum Polish on my motorcycle aluminum parts without anything else once a year. It does an excellent job without having to worry about anything flaking or peeling off.
  23. Replies
    5
    Views
    648

    Try to set up for a turn by slowing down before...

    Try to set up for a turn by slowing down before entering and then power through the turn.
  24. Replies
    3
    Views
    803

    A couple more questions for someone using a pull...

    A couple more questions for someone using a pull starter on a 523 or 323.

    Are any of you running the 01901-323210 back plate and if so what pull starter are you using.

    The reason I'm asking is...
  25. Replies
    133
    Views
    5,243

    that actually sounds like a perfect tune!

    that actually sounds like a perfect tune!
Results 1 to 25 of 167
Page 1 of 7 1 2 3 4