Search:

Type: Posts; User: Ken448

Page 1 of 20 1 2 3 4

Search: Search took 0.26 seconds.

  1. Thread: Rat Rod!

    by Ken448
    Replies
    13
    Views
    1,588

    Hope you made it 2wd if you are planning on...

    Hope you made it 2wd if you are planning on running that tire setup. The front tires are going to be pushed by the rears, and the car will be hard to control due to the difference in diameters.
  2. Thread: it is gone

    by Ken448
    Replies
    121
    Views
    5,007

    I donno.. am I the only one her that has a hard...

    I donno.. am I the only one her that has a hard time believing that motor was under water long enough to corrode the screws off (un likely) BUT not long enough to even leave a mark on the motor.
    ...
  3. Replies
    8
    Views
    452

    Welcome! Might I suggest these on the next...

    Welcome!
    Might I suggest these on the next order.
    http://www.liquidrc.com/index.php?main_page=product_info&cPath=0&products_id=61833
    Since I see yours are leaking already.
  4. Replies
    4
    Views
    157

    you need to clean your camera lense :)

    you need to clean your camera lense :)
  5. Replies
    9
    Views
    351

    Lower the truck, add a little more camber (to get...

    Lower the truck, add a little more camber (to get the truck off the outside edge of the tires while cornering). Mine will corner pretty well on cement. Ill have to get my daughter to make a vid one...
  6. Replies
    15
    Views
    625

    a single 3s and some traction is all I ever...

    a single 3s and some traction is all I ever needed for standing back flips. Did them most on blacktop.
  7. Thread: Shocks

    by Ken448
    Replies
    7
    Views
    246

    GTR's are simply an aluminum copy of the...

    GTR's are simply an aluminum copy of the stockers. I run these:
    http://www.liquidrc.com/index.php?main_page=product_info&cPath=0&products_id=61833
    Since the bottom caps screw on, it doesnt matter...
  8. Replies
    10
    Views
    262

    mine hits in the rear. T Bone says its normal,...

    mine hits in the rear. T Bone says its normal, and if I wanna trim it to fully extend the arms (no need, really) thats fine, the warranty will be good as long as (if) the plate ever breaks, its not...
  9. Replies
    8
    Views
    233

    tip for the future: Disposable turkey sized...

    tip for the future:
    Disposable turkey sized pan. Buy one, re-use it. Keeps the wife happy!
  10. Thread: Center Diff?

    by Ken448
    Replies
    7
    Views
    412

    makes the MERV a whole new truck. Only way to...

    makes the MERV a whole new truck. Only way to know if its for you is try it out. $20 is cheap for an experiment in this hobby.
  11. Replies
    13
    Views
    338

    mine handles great with 50k in the center diff. ...

    mine handles great with 50k in the center diff. Will still wheelie if I REALLY want it to, but other than that, its planted. The key to filling a diff is FILLING it. Any part of the diff isnt...
  12. Replies
    107
    Views
    5,136

    if you have another trx bulkhead.. maybe try...

    if you have another trx bulkhead.. maybe try boiling it before you install it?
  13. Replies
    47
    Views
    2,293

    you NEED to add some vertical bracing to go with...

    you NEED to add some vertical bracing to go with the horizontal bracing. All this work, and it is just going to bend right in the middle within a couple runs. If not on the first run. Id add some...
  14. Replies
    107
    Views
    5,136

    What are the temps locally? I drive all the time...

    What are the temps locally? I drive all the time in sub freezing temps (20F or -6C) here in Detroit doing speed runs, jumps backflips and wheelies. I dont break often (I DO have a T Bone skid, RPM...
  15. Replies
    107
    Views
    5,136

    wow.. what on earth are you doing to that...

    wow.. what on earth are you doing to that thing!?!
  16. Thread: Cleaning

    by Ken448
    Replies
    14
    Views
    406

    I clean my MERV with snow

    I clean my MERV with snow
  17. Replies
    107
    Views
    5,136

    yup, its the one thing INtegy makes thats def a...

    yup, its the one thing INtegy makes thats def a nice addition! If they even make it, that is!
  18. Replies
    107
    Views
    5,136

    man that BL setup isnt treating you well at all!

    man that BL setup isnt treating you well at all!
  19. Replies
    12
    Views
    329

    well they dont recommend it, but it did just fine

    well they dont recommend it, but it did just fine
  20. Replies
    12
    Views
    329

    haha the FIRST thing I did with my MERV out of...

    haha the FIRST thing I did with my MERV out of the box was submerge it and drive under water.. Had to prove to myself it was sealed up and could really handle it.
  21. Replies
    10
    Views
    153

    try unplugging the steering servo and report back.

    try unplugging the steering servo and report back.
  22. Thread: Jumping

    by Ken448
    Replies
    15
    Views
    404

    Simple concept. Thicker oil slows the rebound...

    Simple concept. Thicker oil slows the rebound rate (truck returns to normal ride height slower and smoother) 50wt is stock, I think
    Springs are available in all ranges. Stock, the truck is pretty...
  23. Replies
    22
    Views
    392

    Same here.. Im 30 mi north of the border off I75...

    Same here.. Im 30 mi north of the border off I75 and can help as well
  24. Replies
    11
    Views
    394

    keep the rubber side down!!!!!!!!!

    keep the rubber side down!!!!!!!!!
  25. Replies
    107
    Views
    5,136

    how much is the floating MERV kit? :P

    how much is the floating MERV kit? :P
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4