Search:

Type: Posts; User: Shandley

Page 1 of 3 1 2 3

Search: Search took 0.15 seconds.

  1. Sweet! Well, thanks to all! This is actually fun...

    Sweet! Well, thanks to all! This is actually fun now! :) Only 10 engine rebuilds and a few broken parts but it seems like I am running well now. Time for rebuilt break-in

    Thanks again!

    Here are...
  2. The LSN is still too lean? I took the air...

    The LSN is still too lean?

    I took the air filter off to check the gap just before the video.

    I also took the temp readings close first before the video and they are the same (I'm a...
  3. Ok, I got the truck to the point where it runs...

    Ok, I got the truck to the point where it runs good but still idles high. There is no way I have more than 1mm gap. I have a video coming...

    I am on location rigt now and my batteries are dying on...
  4. Alrighty. Thank you both. I'll try that but I...

    Alrighty. Thank you both. I'll try that but I feel I have done that already. Say, anyone willing to Skype with me to try and get it up and going? You can see live video and give advice that way.
  5. Ok, I ran it again and it ran but high idle. You...

    Ok, I ran it again and it ran but high idle. You can see in the video that any attempt to reduce the idle results on stalling. Any thoughts?

    VideoCheck out this video on YouTube: ...
  6. I actually replaced the back plate and shaft...

    I actually replaced the back plate and shaft because of a small leak that soaked the 1 way bearing and rendered it useless. Everything is sealed back there. Thanks though. I pressure tested the gas...
  7. The needles are straight. I just took the carb...

    The needles are straight. I just took the carb apart again and it is good. I checked for evidence of pinched o-rings but everything looks good. I rolled the needles and they are better that I would...
  8. I'm seriously going to kick this thing right out the window and watch it explode

    Ok, I'm not THAT frustrated but I have less faith than before.

    I will take my truck outside, put the wand on, push the starter button and it will start. Then it will fluctuate in RPM quite...
  9. Replies
    1
    Views
    182

    Low Speed Spray Bar

    Greetings,

    I am rebuilding my carb. I found a Low "Speed Spray Bar" which ios a brass piece that goes opposite of the low speed needle.

    There is a hole that goes right though this small bar....
  10. Replies
    22
    Views
    2,211

    LOL! It took a week but I really appreciate this....

    LOL! It took a week but I really appreciate this.

    I essentially thought that once the gears grip each other without slipping but not pressed against each other so hard that it's more likely to...
  11. Replies
    22
    Views
    2,211

    I have seen nothing on aligning the engine. How...

    I have seen nothing on aligning the engine. How is it suppose to be seated?
  12. Replies
    8
    Views
    352

    Getting into this truck was my first real...

    Getting into this truck was my first real experience with the tiny two strokes. The engine is pretty low on hours (I'm told 15 tanks or so) but they guy before me likes to jump head into things. He...
  13. Replies
    8
    Views
    352

    Thanks. I actually have the TRX 15 Pro engine.

    Thanks. I actually have the TRX 15 Pro engine.
  14. Replies
    8
    Views
    352

    Thanks. Everything looks ok. Good to know it...

    Thanks. Everything looks ok. Good to know it happens. The piston looks pristine! The sleeve (at least the inside) also looks brand new. The saft is unscorn from the damage. I think I'm good to go! Is...
  15. Replies
    8
    Views
    352

    Busted Connecting Rod

    Greetings!

    I was out for a run during my coffee break and the engine suddenly stopped at a pretty high RPM (nothing out of this world high but higher).

    I dismantled the engine and found a...
  16. Replies
    22
    Views
    2,211

    The clutch bell will freely spin and will spin...

    The clutch bell will freely spin and will spin for 10 minutes without the engine mounted and not contacting the spur gear (and if I actually spin it.:) something has to make it go). I assume that is...
  17. Replies
    22
    Views
    2,211

    Can't. Broken head. :(

    Can't. Broken head. :(
  18. Replies
    22
    Views
    2,211

    After 5 min of running and 5 fast passes, the...

    After 5 min of running and 5 fast passes, the head temp was 270. I won't hold anything against anyone but that seems ok, yes?
  19. Replies
    22
    Views
    2,211

    Well, I took the whole engine apart, and the carb...

    Well, I took the whole engine apart, and the carb and cleaned it all out. Very unfortunate, I broke the head off of the LSN. It's set but no more tuning until I get a new carb.

    I am actually 4.25...
  20. Replies
    5
    Views
    125

    Yep! That's it and you are correct! My old one...

    Yep! That's it and you are correct! My old one was covered in grime to the point where I could not see it, no matter how many baths it took.

    Thanks very much! Matter closed.
  21. Replies
    5
    Views
    125

    Thanks buuuuuut I do not see the copper ring. I...

    Thanks buuuuuut I do not see the copper ring. I thought the small circle between the two dotted lines for the posts was it but that's just a post hole.
  22. Replies
    5
    Views
    125

    Starter Gear Set - Copper ring?

    Greetings,

    I have an EZ Start (first one that went on the .15, .12 engines). I broke some gears. I bought a kit to replace them. It comes with the 3 gears, two shafts, and a copper ring. Can...
  23. Replies
    22
    Views
    2,211

    I'll likely just keep it around the play with ...

    I'll likely just keep it around the play with

    VIDEO WITH NEW FUEL & GLOW PLUG
  24. Replies
    22
    Views
    2,211

    I will take my engine completely apart, clean it...

    I will take my engine completely apart, clean it and put it back together. It usually runs right away but with 2 or more full turns out of the high speed needle. I think, as a result, I am getting...
  25. Replies
    22
    Views
    2,211

    Tuning woes. Fuel perhaps?

    Greetings,

    Tuning (or even starting) my .15 Pro is a pain. I have checked everything and sealed everything. I'm going to try a couple more things before I chuck it. I've tried stock settings and...
Results 1 to 25 of 51
Page 1 of 3 1 2 3